ࡱ> _ &Zbjbjzyzy ;6b6bQ   8H \  ]h!(!(!!! #Bb# n# ] ] ] ] ] ] ]$^a/]$ # #$$/]!!HD]((($!!-x/($ ]((++!2L&+}-Z]0]+by'b+b+v#0#"(##v#v#v#/]/]%(v#v#v#]$$$$bv#v#v#v#v#v#v#v#v#B : SECTION 102600 WALL AND DOOR PROTECTION GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division01 Specification Sections, apply to this Section. SUMMARY Section Includes: Wall guards. Impact-resistant handrails. Corner guards. End-wall guards. Abuse-resistant wall coverings. Door-edge protection. Door-frame protection. Related Requirements: Section061000 Miscellaneous Carpentry for in-wall blocking for wall mounted rails and accessories. Section087111 "Finish Hardware" for metal protective trim units, according to BHMAA156.6, used for armor, kick, mop, and push plates. SUBMITTALS Product Data: For each type of product. Include construction details, material descriptions, impact strength, dimensions of individual components and profiles, and finishes. Include fire ratings of units recessed in fire-rated walls and listings for door-protection items attached to fire-rated doors. Shop Drawings: For each type of wall and door protection showing locations and extent. Include plans, elevations, sections, and attachment details.[Show handrail design and support spacing required to withstand structural loads.] Samples for Initial Selection: For each type of impact-resistant wall-protection unit indicated, in each color and texture specified. Include Samples of accent strips and accessories to verify color selection. Samples for Verification: For each type of exposed finish on the following products, prepared on Samples of size indicated below: Wall Guards: 12 inches (300 mm) long. Include examples of joinery, corners, [end caps,] [top caps,] and field splices. Handrails: 12 inches (300 mm) long. Include examples of joinery, corners, and field splices. [Corner] [and] [End-Wall] Guards: 12 inches (300 mm) long. Include example top caps. Abuse-Resistant Wall Covering: 6 by 6 inches (150 by 150 mm) square. Door-Surface Protection: 6 by 6 inches (150 by 150 mm) square. Door[-Edge] [and] [-Frame] Protectors: 12 inches (300 mm) long. Product Certificates: For each type of handrail. Material Certificates: For each type of exposed plastic material. Sample Warranty: For special warranty. Maintenance Data: For each type of wall and door protection product to include in maintenance manuals. Include recommended methods and frequency of maintenance for maintaining best condition of plastic covers under anticipated traffic and use conditions. Include precautions against using cleaning materials and methods that may be detrimental to finishes and performance. QUALITY ASSURANCE Installer Qualifications: An employer of workers trained and approved by manufacturer. Product Options: Drawings indicate size, profiles, and dimensional requirements of wall and door protection units and are based on the specific system indicated. Refer to Section014000 "Quality Requirements." Do not modify intended aesthetic effects, as judged solely by Architect, except with Architect's approval. If modifications are proposed, submit comprehensive explanatory data to Architect for review. DELIVERY, STORAGE, AND HANDLING Store wall and door protection in original undamaged packages and containers inside well-ventilated area protected from weather, moisture, soiling, extreme temperatures, and humidity. Maintain room temperature within storage area at not less than 70 degF (21 degC) during the period plastic materials are stored. Keep plastic materials out of direct sunlight. Store plastic wall- and door-protection components for a minimum of 72 hours, or until plastic material attains a minimum room temperature of 70 degF (21 degC). Store corner-guard covers in a vertical position. Store [wall-guard] [and] [handrail] covers in a horizontal position. WARRANTY Special Warranty: Manufacturer agrees to repair or replace components of wall- and door-protection units that fail in materials or workmanship within specified warranty period. Failures include, but are not limited to, the following: Structural failures including detachment of components from each other or from the substrates, delamination, and permanent deformation beyond normal use. Deterioration of metals, metal finishes, plastics, and other materials beyond normal use. Warranty Period: Five years from date of Substantial Completion. PRODUCTS MANUFACTURERS  HYPERLINK "http://www.specagent.com/Lookup?ulid=641" Manufacturers: Subject to compliance with requirements, provide products by one of the following: Balco. Construction Specialties. Korogard Wall Protection Systems. IPC/InPro Door and Wall Protection Systems. Pawling Corporation. Source Limitations: Obtain wall- and door-protection productsof each type from single source from single manufacturer. PERFORMANCE REQUIREMENTS Surface Burning Characteristics: Comply with ASTME84 or UL723; testing by a qualified testing agency. Identify products with appropriate markings of applicable testing agency. Flame-Spread Index: 25 or less. Smoke-Developed Index: 450 or less. Regulatory Requirements: Comply with applicable provisions in [the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA Accessibility Guidelines for Buildings and Facilities] [and] [ICCA117.1][Texas Accessibility Standards (TAS)]. WALL GUARDS RETAIN "CRASH RAIL" PARAGRAPH BELOW FOR SEVERE IMPACT CONDITIONS. Crash Rail: Heavy-duty[,PVC-free] assembly consisting of continuous snap-on plastic cover installed over concealed retainer; designed to withstand impacts. Cover: Extruded rigid plastic, minimum 0.100-inch (2.5-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Continuous Retainer: Minimum 0.080-inch- (2.0-mm-) thick, one-piece, extruded aluminum. End Caps and Corners: Prefabricated, injection-molded plastic; matching color cover; field adjustable for close alignment with snap-on cover. Accessories: Concealed splices and mounting hardware. Mounting: Surface mounted directly to wall. RETAIN "BUMPER RAIL" PARAGRAPH BELOW FOR LESS-SEVERE IMPACT CONDITIONS. Bumper Rail: Standard-duty[,PVC-free] assembly consisting of continuous snap-on plastic cover installed over concealed retainer; designed to withstand impacts. Cover: Extruded rigid plastic, minimum 0.078-inch (2.0-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Continuous Retainer: Minimum 0.080-inch- (2.0-mm-) thick, one-piece, extruded aluminum. End Caps and Corners: Prefabricated, injection-molded plastic; matching color cover; field adjustable for close alignment with snap-on cover. Accessories: Concealed splices and mounting hardware. Mounting: Surface mounted directly to wall. RETAIN "RUB RAIL" PARAGRAPH BELOW FOR WHEEL PROTECTION BETWEEN CRASH OR BUMPER RAILS AND THE FLOOR. THEY ARE ALSO CALLED "ACCENT RAILS. Rub Rail: Standard-duty[,PVC-free] assembly consisting of continuous snap-on cover installed over concealed, continuous retainer. Cover: Extruded plastic, minimum 0.078-inch (2.0-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Retainer: Minimum 0.0625-inch- (1.6-mm-) thick, one-piece, extruded aluminum. End Caps and Corners: Prefabricated, injection-molded plastic; color matching cover; field adjustable for close alignment with snap-on cover. Accessories: Concealed splices and mounting hardware. Mounting: Surface mounted directly to wall. IMPACT-RESISTANT HANDRAILS Structural Performance: Handrails, including attachment to building construction, shall withstand the effects of gravity loads and the following loads and stresses within limits and under conditions indicated: Uniform load of 50 lbf/ft. (0.73 kN/m) applied in any direction. Concentrated load of 200 lbf (0.89 kN) applied in any direction. Uniform and concentrated loads need not be assumed to act concurrently. Plastic, Impact-Resistant Handrails: Manufacturer's standard[,PVC-free] assembly consisting of snap-on plastic cover installed over continuous retainer. Cover: Minimum 0.078-inch- (2.0-mm-) thick, extruded rigid plastic; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Retainer: Minimum 0.080-inch- (2.0-mm-) thick, one-piece, extruded aluminum. Mounting Bracket: Extended mounting on injection-molded plastic mounting brackets. End Caps and Corners: Prefabricated, injection-molded plastic; matching color cover; field adjustable for close alignment with snap-on cover. Accessories: Concealed splices, cushions, and mounting hardware. CORNER GUARDS Surface-Mounted, Plastic-Cover Corner Guards: Manufacturer's standard[,PVC-free] assembly consisting of snap-on, resilient plastic cover installed over retainer; including mounting hardware; fabricated with 90- or 135-degree turn to match wall condition. Cover: Extruded rigid plastic, minimum 0.078-inch (2.0-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Continuous Retainer: Minimum 0.060-inch- (1.5-mm-) thick, one-piece, extruded aluminum. Retainer Clips: Manufacturer's standard impact-absorbing clips. Top and Bottom Caps: Prefabricated, injection-molded plastic; color matching cover; field adjustable for close alignment with snap-on cover. Flush-Mounted, Plastic-Cover Corner Guards: Manufacturer's standard[,PVC-free] assembly consisting of snap-on, resilient plastic cover that is flush with adjacent wall surface, installed over retainer; including mounting hardware; fabricated with 90- or 135-degree turn to match wall condition; full wall height. Cover: Extruded rigid plastic, minimum 0.078-inch (2.0-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Continuous Retainer: Minimum 0.060-inch- (1.5-mm-) thick, one-piece, extruded aluminum. CORNER GUARDS NEED TO BE FIRE RATED ONLY IF THEY ARE RECESSED IN FIRE-RATED WALLS. Fire-Rated, Flush-Mounted, Plastic-Cover Corner Guards: Manufacturer's standard[,PVC-free] assembly consisting of snap-on, resilient plastic cover that is flush with adjacent wall surface, installed over continuous retainer and intumescent fire barrier; including mounting hardware; fabricated with 90- or 135-degree turn to match wall condition; full wall height. Fire Rating: Same rating as wall in which corner guard is installed; UL listed and labeled according to ASTME1966 or UL2079. RETAIN "L-RATING AT SMOKE BARRIERS" SUBPARAGRAPH BELOW IF ONE OR MORE FLUSH-MOUNTED CORNER GUARDS ARE INSTALLED IN A FIRE-RATED SMOKE BARRIER. L-Rating at Smoke Barriers: Not exceeding 5.0 cfm/ft. (0.00775 cu. m/s x m) of joint at 0.30 inch wg (74.7 Pa) at both ambient and elevated temperatures according to UL2079. Cover: Extruded rigid plastic, minimum 0.078-inch (2.0-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Retainer: Minimum 0.070-inch- (1.8-mm-) thick, one-piece, extruded aluminum. Surface-Mounted, Transparent-Plastic Corner Guards: Fabricated as one piece from clear polycarbonate plastic sheet; with formed edges; fabricated with 90- or 135-degree turn to match wall condition; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Thickness: Minimum 0.075 inch (1.9 mm). Mounting: Countersunk screws through factory-drilled mounting holes. Surface-Mounted, Metal Corner Guards: Fabricated as one piece from formed or extruded metal with formed edges; with 90- or 135-degree turn to match wall condition; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Material: Stainless-steel sheet, Type304. Thickness: Minimum 0.0500 inch (1.3 mm). Finish: Directional satin, No.4. Mounting: [Flat-head, countersunk screws through factory-drilled mounting holes] [Adhesive]. END-WALL GUARDS Surface-Mounted, Plastic-Cover, End-Wall Guard: Manufacturer's standard[,PVC-free] assembly consisting of snap-on, resilient plastic cover installed over continuous retainer; including mounting hardware. Cover: Extruded rigid plastic, minimum 0.078-inch (2.0-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Retainer: Minimum 0.060-inch- (1.5-mm-) thick, one-piece, extruded aluminum. Top and Bottom Caps: Prefabricated, injection-molded plastic; color matching cover; field adjustable for close alignment with snap-on cover. FIRST OPTION IN "FLUSH-MOUNTED, PLASTIC-COVER, END-WALL GUARD" PARAGRAPH BELOW IS THE MOST COMMON CONFIGURATION. Flush-Mounted, Plastic-Cover, End-Wall Guard: Manufacturer's standard[,PVC-free] assembly consisting of snap-on, resilient plastic cover that is flush with adjacent wall surface and that covers entire end of wall, installed over continuous retainer; including mounting hardware. Cover: Extruded rigid plastic, minimum 0.078-inch (2.0-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Retainer: Minimum 0.060-inch- (1.5-mm-) thick, one-piece, extruded aluminum. END-WALL GUARDS NEED TO BE FIRE RATED ONLY IF THEY ARE RECESSED IN FIRE-RATED WALLS. Fire-Rated, Flush-Mounted, Plastic-Cover, End-Wall Guard: Manufacturer's standard[,PVC-free] assembly consisting of snap-on, resilient plastic cover that is flush with adjacent wall surface and that covers entire end of wall, installed over continuous retainer and intumescent fire barrier; including mounting hardware; full wall height. Fire Rating: Same rating as wall in which end guard is installed; UL listed and labeled according to UL2079. Cover: Extruded rigid plastic, minimum 0.078-inch (2.0-mm) wall thickness; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Retainer: Minimum 0.070-inch- (1.8-mm-) thick, one-piece, extruded aluminum. Surface-Mounted, Metal, End-Wall Guards: Fabricated from one-piece, formed or extruded metal that covers entire end of wall; with formed edges; in dimensions and profiles indicated on Drawings / Interior Finish Legend. Material: Stainless-steel sheet, Type304. Thickness: Minimum 0.0500 inch (1.3 mm). Finish: Directional satin, No.4. Mounting: [Flat-head, countersunk screws through factory-drilled mounting holes] [Adhesive]. ABUSE-RESISTANT WALL COVERINGS Abuse-Resistant Sheet Wall Covering: Fabricated from semirigid, plastic sheet wall-covering material; in dimensions, sizes, height, color and texture indicated on Drawings / Interior Finish Legend. Trim and Joint Moldings: Extruded rigid plastic that matches wall-covering color. Mounting: Adhesive. DOOR-EDGE PROTECTION RETAIN THIS ARTICLE IF PLASTIC DOOR-EDGE PROTECTION IS REQUIRED. DOOR EDGES MAY NEED TO BE UNDERCUT TO OBTAIN SPACE FOR EDGING AND PROPER EDGE CLEARANCE. Door Edging: Fabricated from extruded rigid plastic, minimum 0.040-inch (1.0-mm) wall thickness; formed to fit over door edge without mortising. Shape, Color and Texture: As indicated in Interior Finish Legend on Drawings. Mounting: [Adhesive] [Countersunk screws through factory-drilled mounting holes]. DOOR-FRAME PROTECTION RETAIN "DOOR-FRAME PROTECTOR" OR "DOOR-FRAME PROTECTOR ASSEMBLY." Door-Frame Protector: One piece fabricated from extruded rigid plastic, formed to fit entire door-frame profile; wall thickness, height, color and texture as indicated on Drawings / Interior Finish Legend. Mounting: [Adhesive] [Countersunk screws through factory-drilled mounting holes]. REVISE "DOOR-FRAME PROTECTOR ASSEMBLY" SNAP-ON COVER. Door-Frame Protector Assembly: Assembly consisting of snap-on plastic cover installed over continuous retainer; formed to fit half of door frame on opposite side of door swing. Cover: Extruded rigid plastic, minimum 0.080-inch (2.0-mm) wall thickness; height, corner radius indicated on in dimensions, profiles, color and texture indicated Drawings / Interior Finish Legend. Retainer: Minimum 0.080-inch- (2.0-mm-) thick, one-piece, extruded aluminum. MATERIALS Plastic Materials: Chemical- and stain-resistant, high-impact-resistant plastic with integral color throughout; extruded and sheet material as required, thickness as indicated. Polycarbonate Plastic Sheet: ASTMD6098, S-PC01, Class1 or Class2, abrasion resistant; with a minimum impact-resistance rating of 15 ft.-lbf/in. (800J/m) of notch when tested according to ASTMD256, Test MethodA. Aluminum Extrusions: Alloy and temper recommended by manufacturer for type of use and finish indicated, but with not less than strength and durability properties specified in ASTM B 221 (ASTM B 221M) for Alloy 6063-T5. Stainless-Steel Sheet: ASTM A 240/A 240M. Fasteners: Aluminum, nonmagnetic stainless-steel, or other noncorrosive metal screws, bolts, and other fasteners compatible with items being fastened. Use security-type fasteners where exposed to view. Adhesive: As recommended by protection product manufacturer. HYPERLINK "http://www.arcomnet.com/sustainable_design.aspx?topic=143"Adhesives shall have a VOC content of 70g/L or less. FABRICATION Fabricate wall and door protection according to requirements indicated for design, performance, dimensions, and member sizes, including thicknesses of components. Curved Panels: Preform curved semirigid, abuse-resistant sheet wall covering in factory for radius and sheet thickness as follows: Sheet Thickness of 0.040 Inch (1.0 mm): 24-inch (610-mm) radius. Sheet Thickness of 0.060 Inch (1.5 mm): 36-inch (914-mm) radius. Factory Assembly: Assemble components in factory to greatest extent possible to minimize field assembly. Disassemble only as necessary for shipping and handling. Quality: Fabricate components with uniformly tight seams and joints and with exposed edges rolled. Provide surfaces free of wrinkles, chips, dents, uneven coloration, and other imperfections. Fabricate members and fittings to produce flush, smooth, and rigid hairline joints. FINISHES Protect finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. Appearance of Finished Work: Noticeable variations in same piece are not acceptable. Variations in appearance of adjoining components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. EXECUTION EXAMINATION Examine substrates and wall areas, with Installer present, for compliance with requirements for installation tolerances[,fire rating,] and other conditions affecting performance of the Work. Examine walls to which wall and door protection will be attached for blocking, grounds, and other solid backing that have been installed in the locations required for secure attachment of support fasteners. For wall and door protection attached with adhesive, verify compatibility with and suitability of substrates, including compatibility with existing finishes or primers. Proceed with installation only after unsatisfactory conditions have been corrected. PREPARATION Complete finishing operations, including painting, before installing wall and door protection. Before installation, clean substrate to remove dust, debris, and loose particles. INSTALLATION Installation Quality: Install wall and door protection according to manufacturer's written instructions, level, plumb, and true to line without distortions. Do not use materials with chips, cracks, voids, stains, or other defects that might be visible in the finished Work. Mounting Heights: Install wall and door protection in locations and at mounting heights indicated on Drawings. Accessories: Provide splices, mounting hardware, anchors, trim, joint moldings, and other accessories required for a complete installation. Provide anchoring devices and suitable locations to withstand imposed loads. Where splices occur in horizontal runs of more than 20 feet (6.1m), splice aluminum retainers and plastic covers at different locations along the run, but no closer than 12 inches (305 mm) apart. Adjust end and top caps as required to ensure tight seams. Abuse-Resistant Wall Covering: Install top and edge moldings, corners, and divider bars as required for a complete installation. Door-Frame Protectors: Install on both door jams. RETAIN "FIRE DOORS" PARAGRAPH BELOW IF PRODUCTS ARE REQUIRED FOR FIRE-RATED DOORS. Fire Doors: Install protection according to the listing of each item. CLEANING Immediately after completion of installation, clean plastic covers and accessories using a standard ammonia-based household cleaning agent. Remove excess adhesive using methods and materials recommended in writing by manufacturer. END OF SECTION 10 26 00 FOR MDACC USE ONLY. DELETE THIS PAGE BEFORE ISSUING DOCUMENTS. document revision history IssueDateRevision DescriptionAuthor20190301Original IssuanceRev. 1.Rev. 2Rev. 3 Rev. 4 Rev. 5      MD ANDERSON Project No. XXXXXXMD Anderson PROJECT NAMEA/E Name Issue Description A/E Project No.Month 00, 0000 鶹ӳ wall and DOOR PROTECTIONMD Anderson Cancer Center10 26 00 MS 20190301 PAGE 12 of  NUMPAGES 12 )*   ! # ) h %.\ehqWdtĺģģĕĆwĕĕĆwĕĕĕĆwĆwĆwĕĕhth0J/OJQJ^Jhth0J0OJQJ^Jhth5OJQJ^Jh:!OJQJ^JhthB3KOJQJ^Jh tOJQJ^JhthOJQJ^J h thh th0J. h/r:0J-h th/r:0J-h th=20J- h th=2.*2D & 5 F f |  T + A gd tgd tgd t $a$gd tgd t 8}-o uK5pBtsgd tgd tgd tgd t uK,4?-5@{012@Aadgjtu乬䎁mchtOJQJ^J'jhth2OJQJU^Jhth2OJQJ^J!jhth2OJQJU^JhthOJQJ^Jhth`OJQJ^JhthL OJQJ^Jhth0J/OJQJ^Jhth0J0OJQJ^JhthOJQJ^Jhth5OJQJ^J&F]}u)gd tgd tgd t $a$gd tgd tgd tuv :EOBCfv ! !! " "."""""Z#d#İآؓwؓwİآؓwjؓwİآؓhth2OJQJ^Jhth,OJQJ^Jhth0J/OJQJ^Jhth0J0OJQJ^Jhth5OJQJ^J&h'h5<CJOJQJ^JaJ&h'h'5<CJOJQJ^JaJhthOJQJ^Jhth5OJQJ^JhthOJQJ^J)9fO =!!".""9##$$$%#%%6&w&&Y''5((gd tgd t)gd tgd td#m#######$$&&&K&R&\&&'h's'}''''(())*****+++$+.+e,o,-----..#.I..&h'h'5<CJOJQJ^JaJhth_OJQJ^Jhth .8OJQJ^Jhth5OJQJ^Jhth0J0OJQJ^JhthOJQJ^Jhth,OJQJ^JhthOJQJ^Jhth0J/OJQJ^J1()W)e)e**T++!,[--I.. 0011_2233,45F5o5gd t)gd tgd tgd tgd t....00011D1O1e1r1~11112D2]2q2|22q333333345F5Y5d5m5߰ߡߡߡߡ߅ߡ߅߅xiZhthW0J/OJQJ^JhthW0J0OJQJ^JhthWOJQJ^JhthuOJQJ^Jhth0J/OJQJ^Jhth0J0OJQJ^J&h'h'5<CJOJQJ^JaJhth_OJQJ^Jhth5OJQJ^JhthOJQJ^J&h'h5<CJOJQJ^JaJ#m5o5v5w55555G6Q6667G7`7t777<88888999@:C:[:m:x:::::O;Y;[<]<<<<:=漭漭晅漭x漭晅k漭hth5YOJQJ^JhthOJQJ^J&h'h5<CJOJQJ^JaJ&h'h'5<CJOJQJ^JaJhth0J/OJQJ^Jhth0J0OJQJ^Jhth5OJQJ^JhthuOJQJ^JhthOJQJ^JhthWOJQJ^J*o55556b77<889[:::P<<U==}>>>>Q?p?6@@)gd tgd tgd tgd tgd t:===U=g=r=|=0>>>>>>>>????6@ԲAAAA*5=BBBCʻٮʻٮٓʻٮ^ٓ<OJQJ^J&h'h5<CJOJQJ^JaJ&h'h'5<CJOJQJ^JaJhthoOJQJ^Jhth5OJQJ^JhthWOJQJ^Jhth0J/OJQJ^Jhth0J0OJQJ^JhthOJQJ^JhthOJQJ^Jhth5YOJQJ^J$@@@KAA*B|BBBCC*DDEEEFG_HHSIIJJJAKgd t)gd tgd tgd tCCCCCC)D*DE EE&EIEVEXE`EsE}EEEEE.GVpV $a$gd tgd tgd tgd tpVV WWWWXQXkXlXrXwXXX $1$Ifgd t1$gd t$$$d&dNPa$gd t)gd t '$a$gd tgd tgd t)gd t XQXkXXXXYYYYYYYYY!Y8Y9Y;Y?Y@YYYYYYYYYYYYƸͱzkzg`\XkhthZEN hthgh=2htht;OJQJ\]h/r:OJQJ\]#hthtB*OJQJ\]phhthtOJQJ\]hjhU hthh/r:h tOJQJ\] h/r:h/r:h th t5OJQJ\]!h th t;CJOJQJ\]#hh t5;<OJQJ\]XXXXXX\QQQQ $1$Ifgd tkd$$IfTl\ ,$$0$$44 lalyt\TXXXXXXZOOOO $1$Ifgd tkd|$$IfTl\ ,$$0$$44 lalyt\TXXXXXX\QQQQ $1$Ifgd tkd$$$IfTl\ ,$$0$$44 lalyt\TXXXXXXZOOOO $1$Ifgd tkd$$IfTl\ ,$$0$$44 lalyt\TXXXXXX\QQQQ $1$Ifgd tkdp$$IfTl\ ,$$0$$44 lalyt\TXXXXXXZOOOO $1$Ifgd tkd$$IfTl\ ,$$0$$44 lalyt\TXXXXXX\QQQQ $1$Ifgd tkd$$IfTl\ ,$$0$$44 lalyt\TXXXXXXZOOOO $1$Ifgd tkd`$$IfTl\ ,$$0$$44 lalyt\TXXXXXX\QQQQ $1$Ifgd tkd$$IfTl\ ,$$0$$44 lalyt\TXXXXXXZOOOO $1$Ifgd tkd$$IfTl\ ,$$0$$44 lalyt\TXXXXXX\QQQQ $1$Ifgd tkdT$$IfTl\ ,$$0$$44 lalyt\TXXYY Y YZOOOO $1$Ifgd tkd$$IfTl\ ,$$0$$44 lalyt\T Y Y Y YYY\QQQQ $1$Ifgd tkd $$IfTl\ ,$$0$$44 lalyt\TYYYYYYYYYYZRPPPPPPP & Fgd tkdD $$IfTl\ ,$$0$$44 lalyt\T YYYY Y!Y@YYYZYdYwY $$1$Ifa$gdtNkd $$IfTH0x$`64 HaytT$ !$1$Ifa$gdt $1$Ifgdt wYxYYYYYYYJEE@2gd=22gdtNkd $$IfTH0x$`64 HaytT $$1$Ifa$gd/r: $1$IfgdtNkdQ $$IfTH0x$`64 HaytTYYYYYYYYOkd $$IfHU0$ $ l$4 Halyt $$1$Ifa$gdt $1$Ifgdt2gd/r:YYYYYYYYZZZZ Z Z ZZZZZZZ Z!Z"Z$Z%Z&Zʾ䪘pieaZ hthhhZEN hth=2%h\;OJQJ\]mHnHu*)jhtht;OJQJU\]*"h\;OJQJ\]mHnHu&jhtht;OJQJU\]hg;OJQJ\]h';OJQJ\]hthtOJQJ\]htht;OJQJ\]ht;OJQJ\]YYZ Z!Z"Z#ZFA<4gd=24gdtOkd $$IfHU0$ $ &l$4 Halyt $$1$Ifa$gdt $1$IfgdgOkd $$IfHU0$ $ l$4 Halyt#Z$Z%Z&Z & Fgd t4gd/r:91:p<0BP/ =!"#8$% DyK yK jhttp://www.specagent.com/Lookup?ulid=641yX;H,]ą'cDyK yK http://www.arcomnet.com/sustainable_design.aspx?topic=143yX;H,]ą'c$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\T$$Ifl!vh#v#v#v#v:V l0$$5555alyt\Tc$$If!vh#v#v`:V H655`44 HytTc$$If!vh#v#v`:V H655`44 HytTc$$If!vh#v#v`:V H655`44 HytTe$$Ifl!vh#v #v:V HUl$5 544 Halyte$$Ifl!vh#v #v:V HUl$5 544 Halytq$$Ifl!vh#v #v:V HUl$,5 5944 HalytBs666666666vvvvvvvvv666666>6666666666666666666666666666666666666666666666666hH66666666666666666666666666666666666666666666666666666666666666666p62&6FVfv2(&6FVfv&6FVfv&6FVfv&6FVfv&6FVfv&6FVfv8XV~ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@_HmH nH sH tH @`@ NormalOJQJ_HmH sH tH DA`D Default Paragraph FontRi@R 0 Table Normal4 l4a (k ( 0No List 88 HDR$*$a$CJ44 FTR$*$a$CJ:O": tSCT *$5OJQJ^J@O"@ PRT$$ & F*$@&a$5:b: SUT$ & F*$@&a$:b: DST$ & F*$@&a$DORD ART$$$ & F `h*$@&a$BObB @PR1!$ & F `x*$@&a$>Or> >PR2$ & F *$@&a$>O> PR3$ & F *$@&a$>> PR4$ & F  *$@&a$>> PR5$ & F ` *$@&a$0b0 TB1*$^ a$0r0 TB2*$^`a$00 TB3*$^a$00 TB4*$^a$00 TB5*$^ a$00 TF1 *$^ a$00 TF2!*$^`a$00 TF3"*$^a$00 TF4#*$^a$00 TF5$*$^ a$&R& TCH%*$.b. TCE &*$^`p4Or4 EOS'$*$a$5<< ANT (*$a$<>*B* ph<O< 70CMT)$*$a$ <B*ph CPR SPN SPDO NUMO NAM&o& SI B*ph&o& IP B*ph** RJUST1a$4@"4 3?0Header 2H$.1. 2?0 Header Char4 @B4 5?0Footer 4H$.Q. 4?0 Footer Char\b\ 8TIP26NOPQ B* ph8</q< )CMT Char<B*OJQJph4/4 6TIP Char <B* ph8:/: q SAhyperlink >*B*phl 6U 6 q0 Hyperlink >*B*ph>/> @G SustHyperlink >*B* ph =5OMN[<x$d%d&d'd-DM NOPQB* CJ\phR/R <5OMN Char)B* CJOJQJ\fHphq 0/0 B3KPR2 CharOJQJ B3K GTG Level 4NE? ,}nJ &p#'L,0(5} ^}`OJPJQJ^JmHsHtH0/0 "PR1 CharOJQJ*W * 5`Strong5\PK![Content_Types].xmlN0EH-J@%ǎǢ|ș$زULTB l,3;rØJB+$G]7O٭Vc:E3v@P~Ds |w< &R ud#.m5:=CIXY&Z.13578:<=@R (o5@AKpVXXXXXXXXXXXX YYYwYYY#Z&Z/02469;>?ABCDEFGHIJKLMNOPQST1@AAA&RXX  !ttT # @H 0(  0(  B S  ?userSustainabilityTopic_143_1A'R B'RZ[\QQQ'RQQQ'R=*urn:schemas-microsoft-com:office:smarttags PlaceType=*urn:schemas-microsoft-com:office:smarttags PlaceName9*urn:schemas-microsoft-com:office:smarttagsplace / 2 9 < 03:=/6 ORY[&!!!!$$$$''|)~)j.q.-04011r3y377`<g<5?8?BBlPlPQQQQQQQQQ Q!QR RRR$R'R fhtvY[>.G.zGGQQQQQQQ Q!Q$R'R33333333333lPlPQQQQQQQQQQ!Q!QQQQQR RRR#R#R'RlPlPQQQQQQQQQQ!Q!QQQQQR RRR#R#R'RҖd PART -  SCHEDULE  - PRODUCT DATA SHEET  - ``^``.``^``.^`.^`.  ^ `)` ` ^` `) ,RoSs  ZGW0Z 9!\',-2<`:!l!f(0=285 .898/r:b<BGINHs IB3KZEN*O!VOrdSPVWolW5YxanEe`dlw/motw08y ~ug t,_- 3 ~Y"xoL {SqJ)B68|vc,$CZj\5]fQ(?`@G["'6QQDOIFormatMF04MF95MFOriginSpecTypeuserSustainabilityVar_11_1userSustainabilityVar_140_1userSustainabilityVar_143_1userSustainabilityVar_146_1userSustainabilityVar_148_1userSustainabilityVar_17_1userSustainabilityVar_175_1userSustainabilityVar_25_1userSustainabilityVar_26_1userSustainabilityVar_63_1Version06/01/17110260010265MF04 MasterSpec$11^userSustainabilityTopic_11_1^2,^<SustainabilityTopic id="11"><TopicText id="176"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>"Product Data" Subparagraph below applies to LEED 2009 NC, CI, and CS; LEEDv4; IgCC; ASHRAE189.1; and Green Globes. Coordinate with requirements for adhesives.</CMT><PR2>Product Data: For adhesives, indicating VOC content.</PR2></Content> </TopicText><TopicText id="177"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>"Laboratory Test Reports" Subparagraph below applies to LEED 2009 for Schools, LEEDv4, IgCC, ASHRAE189.1, and Green Globes. Coordinate with requirements for adhesives.</CMT><PR2>Laboratory Test Reports: For adhesives, indicating compliance with requirements for low-emitting materials.</PR2></Content> </TopicText><TopicText id="176"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>"Product Data" Subparagraph below applies to LEED 2009 NC, CI, and CS; LEEDv4; IgCC; ASHRAE189.1; and Green Globes. Coordinate with requirements for adhesives.</CMT><PR2>Product Data: For adhesives, indicating VOC content.</PR2></Content> </TopicText><TopicText id="177"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>"Laboratory Test Reports" Subparagraph below applies to LEED 2009 for Schools, LEEDv4, IgCC, ASHRAE189.1, and Green Globes. Coordinate with requirements for adhesives.</CMT><PR2>Laboratory Test Reports: For adhesives, indicating compliance with requirements for low-emitting materials.</PR2></Content> </TopicText></SustainabilityTopic>14014012,<SustainabilityTopic id="140"><TopicText id="577"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>Subparagraph below applies to LEEDv4.</CMT><PR2>Adhesive shall comply with the testing and product requirements of the California Department of Public Health's "Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers."</PR2></Content> </TopicText></SustainabilityTopic>14314312,<SustainabilityTopic id="143"><TopicText id="583"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>Subparagraph below applies to LEED 2009 NC, CI, and CS; LEEDv4; IgCC; ASHRAE189.1; and Green Globes. VOC content limit is that for multipurpose construction adhesives.</CMT><PR2>Adhesives shall have a VOC content of [70] &lt;Insert value&gt;g/L or less.</PR2></Content> </TopicText></SustainabilityTopic>$146^userSustainabilityTopic_146_1^2,^<SustainabilityTopic id="146"><TopicText id="174"><RatingSystems><System id="2"/></RatingSystems> <Content><PR2>Chain-of-Custody Certificates: For certified wood products. Include statement of costs.</PR2></Content> </TopicText></SustainabilityTopic>s148^userSustainabilityTopic_148_1^2,^<SustainabilityTopic id="148"><TopicText id="175"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>"Chain-of-Custody Qualification Data" Subparagraph below applies to LEED 2009 and LEEDv4.</CMT><PR2>Chain-of-Custody Qualification Data: For manufacturer and vendor.</PR2></Content> </TopicText></SustainabilityTopic>171712,<SustainabilityTopic id="17"><TopicText id="189"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>"Laboratory Test Reports" Subparagraph below applies to LEEDv4.</CMT><PR2>Laboratory Test Reports: For composite wood products, indicating compliance with requirements for low-emitting materials.</PR2></Content> </TopicText></SustainabilityTopic>17517512,<SustainabilityTopic id="175"><TopicText id="647"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>"Certified Wood" Subparagraph below applies to LEEDv4. Manufacturers certifying products as "FSC Mixed Credit" do not have to use 100 percent certified wood in the products; however, in their total production, manufacturers must use an amount equal to or greater than the percentage of their production that is labeled "FSC Mixed Credit."</CMT><PR2>Certified Wood: Wood products shall be certified as "FSC Pure"[or "FSC Mixed Credit"] according to FSCSTD-01-001 and FSCSTD-40-004.</PR2></Content> </TopicText></SustainabilityTopic>252512,<SustainabilityTopic id="25"><TopicText id="225"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>Retain "Manufacturer Qualifications" Paragraph below if required for LEEDv4.</CMT><PR1>Manufacturer Qualifications: A qualified manufacturer that is certified for chain of custody by an FSC-accredited certification body.</PR1></Content> </TopicText></SustainabilityTopic>262612,<SustainabilityTopic id="26"><TopicText id="227"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>Retain "Vendor Qualifications" Paragraph below if required for LEEDv4.</CMT><PR1>Vendor Qualifications: A vendor that is certified for chain of custody by an FSC-accredited certification body.</PR1></Content> </TopicText></SustainabilityTopic>-63^userSustainabilityTopic_63_1^2,^<SustainabilityTopic id="63"><TopicText id="353"><RatingSystems><System id="2"/></RatingSystems> <Content><CMT>"Composite Wood Products" Paragraph below applies to LEEDv4.</CMT><PR1>Composite Wood Products: Products shall be made using ultra-low-emitting formaldehyde resins as defined in the California Air Resources Board's "Airborne Toxic Control Measure to Reduce Formaldehyde Emissions from Composite Wood Products" or shall be made with no added formaldehyde.</PR1></Content> </TopicText></SustainabilityTopic>13782@&R@UnknownG.[x Times New Roman5Symbol3. .Cx Arial7. [ @Verdana7.*{$ CalibriA$BCambria Math"1hh\t% D ) D )%PPJqHP  $P?2!xx )SECTION 102600 - WALL AND DOOR PROTECTIONWALL AND DOOR PROTECTIONBAS-12345-MS80Fitzgerald,Richard W Oh+'0  <H h t ,SECTION 102600 - WALL AND DOOR PROTECTIONWALL AND DOOR PROTECTIONBAS-12345-MS80NormalFitzgerald,Richard W37Microsoft Office Word@HR7@6vz@,L  D13b8e05c2athttp://fm/groups/cpm/TRG/odgCollaboration/_layou OTECTION Title| ts/15/DocIdRedir.aspx?ID=SZWXXFYDWACR-487-703, SZWXXFYDWACR-487-0FUWNHS==2p_p+_Item 22PropertiesJ <  !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUWXYZ[\]_`abcdefghijklmnopqrstuvwxyz{|}~Root Entry Fp+_Data V1Table^bWordDocument ;SummaryInformation(DocumentSummaryInformation87MsoDataStore p_p+_M401UMVLP==2p_p_Item  PropertiesCompObj rPN55YG2LU2JRHCS==2 p_p_  !"#$%&')*+-/01345689:;<=>?DocumentLibraryFormDocumentLibraryFormDocumentLibraryFormlectedStyle="\APASixthEditionOfficeOn tp://schemas.openxmlformats.org/officeDocument/2006/cus sion="1.0" encoding="UTF-8" standalone="no"?> Document ID GeneratItem  x.PropertiesBUWGR4YJPXM1Q==2p_p+_Item eProperties(VDUPCGRFOIRT==2p_p+_Item ,Properties./xsd:simpleType> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. orSynchronous100011000Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100021001Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100041002Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100061003Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandler.0.0, Culture=neutral, Publ ronization>Synchronous10006 sion="1.0" encoding="UTF-8" standalone="no"?> gProperties"/> ՜.+,D՜.+,p, px  AVITRU, LLC.T)P *SECTION 102600 - WALL AND DOOR PROTECTION Titlep X$` @ ` _PID_HLINKS _dlc_DocId_dlc_DocIdItemGuid_dlc_DocIdUrl Published Date to External SiteReady to PublishStatus CSI DivisionA4 R6:http://www.arcomnet.com/sustainable_design.aspx?topic=143E)http://www.specagent.com/Lookup?ulid=641SZWXXFYDWACR-487-703%bfc08970-726b-4db4-b767-8c