ࡱ> a @bjbjjj G?b?b7- TTTTThhh8$h^0(. ^^^^^^^$_b9^T! ! ! 9^TTN^4$$$! TT^$! ^$$bW\x}J"vZj]^<^ [vc"c\cT\dhiJ$<29^9^#B^! ! ! ! c B : SECTION 10 28 13 toilet and bath accessories GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General Conditions and Division 01 Specification Sections, apply to this Section. SUMMARY This Section includes the following: Toilet and bath accessories. Infant-care products. REFERENCE STANDARDS The latest published edition of a reference shall be applicable to this Project unless identified by a specific edition date. Reference amendments adopted prior to the effective date of this Contract shall be applicable to this Project. Materials, installation and workmanship shall comply with all applicable requirements and standards. QUALITY ASSURANCE Inserts and Anchorages: Furnish accessory manufacturers' standard inserts and anchoring devices that must be set in concrete or built into masonry. Coordinate delivery with other Work to avoid delay. [NORMALLY DELETE BELOW IF PROPRIETARY LISTING OF MFRS INCLUDED in accessory schedule.] [ARCHITECT/ENGINEER MUST DELETE EVERYTHING IN BLUE AND IN BRACKETS BEFORE PUBLISHING.] Single Source Responsibility: Provide products of same manufacturer for each type of accessory unit and for units exposed to view in same areas, unless otherwise acceptable to Architect. SUBMITTALS Product Data: Submit manufacturer's product data and installation/maintenance instructions for all manufactured products and materials. Shop Drawings: Submit a complete listing of all manufacturers, products, model numbers, locations, and designs proposed for use. Record Documents: Provide record approved product data and shop drawings. PROJECT CONDITIONS Coordination: Coordinate accessory locations, installation, and sequencing with other Work to avoid interference with and ensure proper installation, operation, adjustment, cleaning, and servicing of toilet accessory items. PRODUCTS GENERAL Materials shall meet or exceed all applicable referenced standards, federal, state and local requirements, and conform to codes and ordinances of authorities having jurisdiction. manufacturers The notes and schedules on the Drawings establish manufacturer and design required for the Project. Subject to compliance with requirements, manufacturers offering toilet accessories that may be incorporated in the Work include, but are not limited to, the following: American Specialties, Inc. Bradley Corporation. Bobrick Washroom Equipment, Inc. GAMCO Georgia-Pacific LLC. MATERIALS, GENERAL [SELECT, REVISE, OR DELETE MATERIALS AND FINISHES BELOW TO SUIT PROJECT REQUIREMENTS.] Stainless Steel: ASTM A 666, Type 304, with polished No. 4 finish, 0.034 inch (22 gage) minimum thickness. Brass: Leaded and unleaded, flat products, ASTM B 19; rods, shapes, forgings, and flat products with finished edges, ASTM B 16; Castings, ASTM B 30. Sheet Steel: Cold rolled, commercial quality ASTM A 1008/A 1008 M, 0.036 inch (20 gage) minimum. Surface preparation and metal pretreatment as required for applied finish. Galvanized Steel Sheet: ASTM A 653/A 653 M, with G60 hot-dip zinc coating. Chromium Plating: Nickel and chromium electro deposited on base metal, ASTM B 456, Type SC 2. [SOME MANUFACTURERS PROVIDE BOTH BRASS AND STEEL WITH CHROME FINISH.] Baked Enamel Finish: Factory applied, gloss white, baked acrylic enamel coating. Stainless Steel Mirror Surfaces: Not less than 0.04 inch (20 gage) AISI Type 302/304 stainless steel sheet, stretcher leveled with No. 8 polished mirror finish. Bond to 1/4 inch minimum hardboard backing. Galvanized Steel Mounting Devices: ASTM A 153, hot dip galvanized after fabrication. Fasteners: Screws, bolts, and other devices of same material as accessory unit, or of galvanized steel where concealed. FABRICATION Names or labels are not permitted on exposed faces of toilet and bath accessory units. On either interior surface not exposed to view or on back surface, provide identification of each accessory item either by a printed, waterproof label or a stamped nameplate indicating manufacturer's name and product model number. Surface Mounted Toilet Accessories, General: Except where otherwise indicated, fabricate units with tight seams and joints, exposed edges rolled. Hang doors or access panels with continuous stainless steel piano hinge. Provide concealed anchorage wherever possible. Recessed Toilet Accessories, General: Except where otherwise indicated, fabricate units of all welded construction, without mitered corners. Hang doors or access panels with full length, stainless steel piano hinge. Provide anchorage that is fully concealed when unit is closed. Framed Mirror Units, General: Fabricate frames for glass mirror units to accommodate wood, felt, plastic, or other glass edge protection material. Provide mirror backing and support system that will permit rigid, tamperproof glass installation and prevent moisture accumulation, as follows: Provide galvanized steel backing sheet, not less than 0.034 inch (22 gage) and full mirror size, with non absorptive filler material. Corrugated cardboard is not an acceptable filler material. Mirror Unit Hangers: Provide system for mounting mirror units that will permit rigid, tamperproof, and theft proof installation, as follows: One piece galvanized steel, wall hanger device with spring action locking mechanism to hold mirror unit in position with no exposed screws or bolts. Heavy duty wall brackets of galvanized steel, equipped with concealed locking devices requiring a special tool to remove. Keys: Provide universal keys for access to toilet accessory units requiring internal access for servicing, re-supply, etc. Provide minimum of six keys to Owner's representative. EXECUTION INSTALLATION Installation shall meet or exceed all applicable federal, state and local requirements, referenced standards and conform to codes and ordinances of authorities having jurisdiction. Installation shall be in accordance with manufacturers published recommendations. Install toilet accessory units according to manufacturers' instructions, using fasteners appropriate to substrate as recommended by unit manufacturer. Install units plumb and level, firmly anchored in locations and at heights indicated. Secure mirrors to walls in concealed, tamperproof manner with special hangers, toggle bolts, or screws. Set units plumb, level, and square at locations indicated, according to manufacturer's instructions for type of substrate involved. Install grab bars to withstand a downward load of at least 400 lbf, complying with ASTM F 446 test methods. ADJUSTING AND CLEANING Adjust toilet accessories for proper operation and verify that mechanisms function smoothly. Replace damaged or defective items. Clean and polish all exposed surfaces strictly according to manufacturer's recommendations after removing temporary labels and protective coatings. TOILET AND BATH ACCESSORY SCHEDULE A1 Sanitary Napkin Dispenser: Material: Stainless steel. Construction: All-welded with continuous stainless steel piano hinge, tumbler locks. Mounting: Recessed in wall. Capacity: 30 napkins and 20 tampons. Coin Denomination: As selected by Architect. Basis of Design Product: Bobrick B-3706. B1 Grab Bars: Sizes: Refer to Drawings. Material: Stainless Steel, 18 gage, type 304, satin finish. Construction: 1-1/2 inch clearance between grab bar and wall. Mounting: Concealed plates with no exposed fasteners. Basis of Design Product: Bobrick B-6806 X 12. B2 Grab Bars: Sizes: Refer to Drawings. Material: Stainless Steel, 18 gage, type 304, satin finish. Construction: 1-1/2 inch clearance between grab bar and wall. Mounting: Concealed plates with no exposed fasteners. Basis of Design Product: Bobrick B-6806 X 18. B3 Grab Bars: Sizes: Refer to Drawings. Material: Stainless Steel, 18 gage, type 304, satin finish. Construction: 1-1/2 inch clearance between grab bar and wall. Mounting: Concealed plates with no exposed fasteners. Basis of Design Product: Bobrick B-6806 X 24. B4 Grab Bars: Sizes: Refer to Drawings. Material: Stainless Steel, 18 gage, type 304, satin finish. Construction: 1-1/2 inch clearance between grab bar and wall. Mounting: Concealed plates with no exposed fasteners. Basis of Design Product: Bobrick B-6806 X 30. B5 Grab Bars: Sizes: Refer to Drawings. Material: Stainless Steel, 18 gage, type 304, satin finish. Construction: 1-1/2 inch clearance between grab bar and wall. Mounting: Concealed plates with no exposed fasteners. Basis of Design Product: Bobrick B-6806 X 36. B6 Grab Bars: Sizes: Refer to Drawings. Material: Stainless Steel, 18 gage, type 304, satin finish. Construction: 1-1/2 inch clearance between grab bar and wall. Mounting: Concealed plates with no exposed fasteners. Basis of Design Product: Bobrick B-6806 X 42. C Mirror, Framed: Material: No. 1 quality, 1/4 inch select float glass, 20 gage galvanized steel back and stainless steel retainer angle; channel frame with mitered corners. Size: 18 inches wide by 30 inches high. Mounting: Concealed hangers. Basis of Design Product: Bobrick B-290. D1 Sanitary Napkin Disposal, Recessed in Wall: Material: Stainless steel. Construction: All-welded with continuous stainless steel piano hinge. Door: Push type, self-closing. Mounting: Recessed in wall. Receptacle: Leak proof, plastic, removable; capacity 1.2 gallons. Basis of Design Product: Bobrick B-353. D2 Sanitary Napkin Disposal, Surface Mounted: Material: Stainless steel. Door: Tumbler lock. Mounting: Surface mounted. Receptacle: Leak proof, plastic, removable; capacity 1.2 gallons. Basis of Design Product: Bobrick B-254. D3 Sanitary Napkin Disposal, Partition: Material: Stainless steel, 22 gage door and flanges. Construction: All-welded with continuous stainless steel piano hinge. Door: Push type, self-closing. Mounting: In toilet partition serving two compartments. Receptacle: Leak proof, plastic, removable; capacity 1.2 gallons. Basis of Design Product: Bobrick B-354. E Toilet Tissue Dispenser, Double Roll: Material: Satin-finish stainless steel. Capacity: Two standard core tissue rolls up to 10 inches diameter. Mounting: Surface. Basis of Design Product: Bobrick B-2892. F1 Paper Towel Dispenser, Recessed: Material: Stainless steel; 22 gage. Mounting: Recessed. Basis of Design Product: Georgia Pacific 59466A F2 Recessed Trash Receptacle: Material: Stainless steel Receptacle: Removable, leakproof, inner plastic container; 12 gallon capacity. Mounting: Recessed. Basis of Design Product: Georgia Pacific 59491 F3 Paper Towel Dispenser, Surface: Mounting: Surface. Basis of Design Product: Georgia Pacific 59462A F4 Paper Towel Dispenser, Surface: Mounting: Surface. Basis of Design Product: Georgia Pacific 59488A F5 Recessed Paper Towel Dispenser/Receptacle: Material: Stainless steel; 22 gage flange, 18 gage door. Construction: Welded door with continuous stainless steel piano hinge; 2 tumbler locks. Receptacle: Removable, leakproof, inner plastic container; 12 gallon capacity. Mounting: Recessed. Dispenser Capacity: 600 C-fold or 800 multifold paper towels. Basis of Design Product: Bobrick B-3944. F6 Paper Towel Dispenser, Surface: Material: Stainless steel, 22 gage. Construction: All-welded. Mounting: Surface. Capacity: 400 C-fold or 525 multi-fold paper towels. Basis of Design Product: Bobrick B-262. G1 Surface Mounted Waste Receptacle: Material: Stainless steel Construction: Welded door with continuous stainless steel piano hinge; 2 tumbler locks. Receptacle: 12.75 gallon capacity. Mounting: Surface Basis of Design Product: Bobrick B-277. G2 Surface Mounted Waste Receptacle: Material: Stainless steel Construction: Welded door with continuous stainless steel piano hinge; 2 tumbler locks. Receptacle: 6.4 gallon capacity. Mounting: Surface Basis of Design Product: Bobrick B-279. H1 - Toilet Seat Cover Dispenser: Material: 22 gage stainless steel. Mounting: Surface Construction: Surface Mounted: All welded; no hinge or lock. Capacity: 250 paper toilet seat covers. Basis of Design Product: Bobrick B-221 I Soap Dispenser, Surface on Wall: Material: ABS Plastic. Capacity: 3/1.25 Liter Mounting: Surface Basis of Design Product: Dial 05028. J1 Single Robe Hook: Material: Stainless steel, 18 gage, type 304, satin finish. Construction: Single-hook, concealed wall plate, no exposed fasteners Mounting: Surface. Basis of Design Product: Bobrick B-6717. J2 Double Robe Hook: Material: Stainless steel, 18 gage, type 304, satin finish. Construction: Double-hook, concealed wall plate, no exposed fasteners Mounting: Surface. Basis of Design Product: Bobrick B-6727. K Toilet Tissue Dispenser, Double Roll: Capacity: Two standard core tissue rolls up to 9 inches diameter. Mounting: Surface. Basis of Design Product: Georgia Pacific 59209. M Toilet Tissue Dispenser, Double Roll: Material: Stainless steel; chrome-plated plastic spindle Capacity: Two standard core tissue rolls up to 5 1/8 inches diameter. Mounting: Surface. Basis of Design Product: Bobrick B-6999. N - Baby Changing Unit: Material: Durable, high-impact polyethylene with foam core. Construction: Bed secured to back plate with a concealed, full-length stainless steel hinge rod with steel bushings embedded in the plastic; equipped with pneumatic cylinder; smooth concave changing area. Mounting: As iIndicated on drawings. Basis of Design Product: GAMCO BCS-1 S Hook Strip Material: Stainless steel, 18 gage, type 304 with exposed surfaces satin finished. Size: Refer to Drawings for lengths. Mounting: Surface. Basis of Design Product: Bobrick B-232 X 36. U - Folding Shower Seat: Materials: Plastic and stainless steel. Seat: Phenolic composite, one-piece construction, reversible. Basis of Design Products: Refer to Drawings for selection. Accessibility Professionals APCSSR2-320225PW (Right hand). Accessibility Professionals APCSSL2-320225PW (Left hand). END OF SECTION 10 28 13 FOR MDACC USE ONLY. DELETE THIS PAGE BEFORE ISSUING DOCUMENTS. document revision history IssueDateRevision DescriptionAuthor20190301Original IssuanceRev. 1.Rev. 2Rev. 3 Rev. 4 Rev. 5    MD ANDERSON Project No. XXXXXXMD ANDERSON PROJECT NAMEA/E Name Issue Description A/E Project No.Month 00, 0000 鶹ӳ toilet and bath accessories MD Anderson Cancer Center10 28 13 MS 20190301 PAGE 12 of  NUMPAGES 12 -GH4 5 H I 6 ? p s z b f w $ % >?2DM j@ABci~׭ hh1h1h3ihhvhh| hhZW" hhBhB hhBhi< h`@h+h+hwh' h@hhT{hgn>.6H  5 I 6 w % t ?R3gdgdgdgdgdgdr>3<D-Bci~TCygdgdgdgdgd %&,13Cyz:Edi"BX!Y![!z!!""/./:1_11133k66Q7v799A:k:>>> hJh+hJhJmH sH  hJhJh+h#_h*d h@hhbhtZhi< hh1h< h/ch3i h1h1h1@`o#-:B0 !!!"""""#j#####$$gd=ugdgdgdgd$0$m$$$$%"%=%z%%% &&/&J&&&&','<'W''' ($(9(I(gdgd=ugdI(d((()1)F)V)q)))$*>*S*g*+-+K+e+t+++,(,E,,,,,gdgd=ugd,,-.-q-----@.`...././W//////$090S0j0000gdgd=ugd0 1$1:1_1s1111112>2x22!363u3333344N4h4w444gdgd=ugd4565I5c5r555 6/6B6\6k66667)7C7Q7v777777718x8gdgd=ugdx88888 9Q9e99999:*:A:k:::;;*;B;;M<s<<<<gd=ugd$gd=ugd<<"=6=P=d=}===!>\>>>>? ???)?0? $Ifgdgd$$$d&d1$NPa$gdgdgdgdgd=ugd>>>?7?????????????????,/<@A@M@N@O@P@g@i@@@@@@@@@@@@@@@@@@@ƾƾƶƶƺƲڪڦڢڦڞږږږږjhU*hgnmHnHujhUhj YhU`hT{hThGhr>h[hgnhB*phhh>~hQ jhQ Uh hgn5hh5hh;CJ hhh10?1?2?3?4?5?^UUUU $Ifgdkd$$IfTl\,$$0$44 layt9T5?6?7?@?R?S?\SSSS $Ifgdkd$$IfTl\,$$0$44 layt9TS?T?U?V?W?X?^UUUU $Ifgdkd8$$IfTl\,$$0$44 layt9TX?Y?`?a?c?d?\SSSS $Ifgdkd$$IfTl\,$$0$44 layt9Td?e?f?g?h?i?^UUUU $Ifgdkdp$$IfTl\,$$0$44 layt9Ti?j?q?r?s?t?\SSSS $Ifgdkd $$IfTl\,$$0$44 layt9Tt?u?v?w?x?y?^UUUU $Ifgdkd$$IfTl\,$$0$44 layt9Ty?z?????\SSSS $IfgdkdB$$IfTl\,$$0$44 layt9T??????^UUUU $Ifgdkd$$IfTl\,$$0$44 layt9T??????\SSSS $Ifgdkdz$$IfTl\,$$0$44 layt9T??????^UUUU $Ifgdkd$$IfTl\,$$0$44 layt9T??????\SSSS $Ifgdkd$$IfTl\,$$0$44 layt9T??????^UUUU $IfgdkdP$$IfTl\,$$0$44 layt9T??????????\WRRRRRPRgdgdkd$$IfTl\,$$0$44 layt9T ?????????????????????????????gd?? @@@+@,@<@K@HKkd$$IfTH0x$`64 HaT $$Ifa$gdKkd$$IfTH0x$`64 HaT $$Ifa$gd $IfgdK@L@M@N@O@P@i@@@@PGkd $$IfHU0$ $ $4 Hal $Ifgd $IfgdgdgdKkdF $$IfTH0x$`64 HaT @@@@@@@@@ZUPNgdgdGkdg $$IfHU0$ $ &$4 Hal $$Ifa$gdw(Gkd $$IfHU0$ $ $4 Hal $Ifgd@@@@@@hQ hjhU*hgnmHnHu*@@gdE....()()))()000?P&P/R 8$BP/ =!"#8$% Dp$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T$$If!vh#v#v#v#v:V l0$5555yt9T]$$If!vh#v#v`:V H655`44 HT]$$If!vh#v#v`:V H655`44 HT]$$If!vh#v#v`:V H655`44 HT_$$Ifl!vh#v #v:V HU$5 544 Hal_$$Ifl!vh#v #v:V HU$5 544 Halk$$Ifl!vh#v #v:V HU$,5 5944 Hal"s2 0@P`p2( 0@P`p 0@P`p 0@P`p 0@P`p 0@P`p 0@P`p8XV~ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@_HmH nH sH tH J`J Normal1$OJQJ\]_HmH sH tH ZZ  Heading 1$ <@&^ ;CJKH \^JaJ RR  Heading 2$ P 1$@&^  5;CJXX  Heading 3$ h!  1$@&^ 5;mH sH DA D Default Paragraph FontVi@V  Table Normal :V 44 la (k (No List P+@P Endnote Text,EOS$1$a$5;.. TOC 9 ^V@V Footnote Text,Foot Title$a$;4/!4 PR2 Char OJQJ]R@2R Header,Head Project  !;4 B4 Footer  !>O> PRT$$ & F1$a$50Ob0 r>TITLE5;POrP !PR10$$ & F `81$^8`a$XOrX ART3$$ & F `01$^`0a$;LOL PR2($$ & F 1$`a$\O =uPR30$$ & F 1$^`a$\Zjg-$$ & F ^`a$OJQJ]_HmH nH sH tH TT PR40$$ & F  p1$^p`a$\TT PR50$$ & F `  1$^ `a$\<O< 0CMT $1$5;B*phBOB Comment5;B*CJphDrD +SUT$*$1$@&a$OJQJ\]DrD +DST $*$1$@&a$OJQJ\]6/6 PR1 CharOJQJ\]PK![Content_Types].xmlN0EH-J@%ǎǢ|ș$زULTB l,3;rØJB+$G]7O٭Vc:E3v@P~Ds |w< 8"',,,/>@@!$-3$(,048<0?5?S?X?d?i?t?y?????????K@@@@"#%&'()*+,./0123456789:;<=>?A $'/!tt8@0(  B S  ? OLE_LINK3 OLE_LINK4 ) )8$)$)8 5 5 5 5 5 5 5T8T8b8t8t8888^8g8g8x8x88889*urn:schemas-microsoft-com:office:smarttagsplace=*urn:schemas-microsoft-com:office:smarttags PlaceName8*urn:schemas-microsoft-com:office:smarttagsCity:*urn:schemas-microsoft-com:office:smarttagsStreet B I v\_ $ + 1!8!>"E"e#l#$$%%&&''''((E)J)))**++++h,o,c-j-\.c.p.v.|..C/J/001111E2K23!3[4e4P5W57777777777788O[ 7777777777788333HH}5}5!6!6\6\6666777777O8P8g8i888888888888888888HH}5}5!6!6\6\66667777777777777777777788,8/8A8A8L8M8888888(|,H8}E"~ WoDp#p$h~I{S|yTX2 E] >4y$*: Kc &r/&H%.X&c}'&Jk3/-ho2ي+#2217t< <&,=qRa@,l@ALk#_ELZdB.L&VTQf=Tsz*F\ `|b&kkn|smJX [oLmszgB {w Qpx:4^`.^`.88^8`.^`. ^`OJQJo( ^`OJQJo( 88^8`OJQJo( ^`OJQJo(hh^h`. hh^h`OJQJo(^`o( PART - ^`o( SCHEDULE  - ^`o(PRODUCT DATA SHEET  - ``^``o(.``^``o(.^`o(.^`o(.  ^ `o()` ` ^` `o()@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.^`o(.^`.pLp^p`L.@ @ ^@ `.^`.L^`L.^`.^`.PLP^P`L.@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.^`o(.^`o(.^`o(.^`o(.^`o(.ww^w`o(ww^w`o(.0^`0o(..0^`0o(... 88^8`o( .... 88^8`o( ..... 88^8`o( ...... `^``o(....... `^``o(........^`o(.^`o(.@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.^`o(^`o(.^`o(..^`o(... ^`o( .... ^`o( ..... ^`o( ...... `^``o(....... `^``o(........^`o(.@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.^`o(.{^`{o(2.03  ^ `o(..  ^ `o(...   ^ `o( ....   ^ `o( .....   ^ `o( ......  ` ^ ``o(.......  ` ^ ``o(........ww^w`o(ww^w`o(.0^`0o(..0^`0o(... 88^8`o( .... 88^8`o( ..... 88^8`o( ...... `^``o(....... `^``o(........^`o(^`o(.^`o(..^`o(... ^`o( .... ^`o( ..... `^``o( ...... `^``o(....... `^``o(........^`o(.^`o(.{^`{o(3.  ^ `o(..  ^ `o(...   ^ `o( ....   ^ `o( .....   ^ `o( ......  ` ^ ``o(.......  ` ^ ``o(........^`o(.^`o(.^`o(.^`o(^`o(.0^`0o(..0^`0o(... 88^8`o( .... 88^8`o( ..... 88^8`o( ...... `^``o(....... `^``o(........@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L. ww^w`o(hH ww^w`o(hH. 0^`0o(hH. 0^`0o(hH... 88^8`o(hH .... 88^8`o(hH ..... 88^8`o(hH ......  `^``o(hH.......  `^``o(hH........^`o(.@^`o(.^`o(.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.*<<Kc `|b <r/.L#_Ec}'kka@o2VT*F\#2=TB {wH% [o217E pxsm,=4yJk3/msl@A ~}|R<0( MASTERSPEC(&        ي+        &        &         Q        &        &        &h        @ @SR\1 < | gn=uJk?r>5"ܰ"w(&+;,ڱ2;:<)BEDEfOERyU_=Vj Y]#_U`b/c3iiEi^j@pxxs45tey>~pKs%[lw6Fa|:8tZ*di$+>OXgTT{Q b( B}'e 7=9?xGv)#77@77778@UnknownFisher, ShelbyG.[x Times New Roman5Symbol3. .Cx Arial7. [ @VerdanaA$BCambria Math"9)h 4tfO_/ eO_/ e!)P4772q)PHP ?^j2!xxs ?@ABDEFGHIJLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}Root Entry FoԿ_Data C1TableKbdWordDocumentGSummaryInformation(~DocumentSummaryInformation8,DCompObjrMsoDataStore oԿ_oԿ_  !"#$%&')*+-./0123456789:;B=?@ACDEFG  F Microsoft Word 97-2003 Document MSWordDocWord.Document.89q DocumentLibraryFUFLBUPEWPGAQ==2 oԿ_oԿ_Item  x.Properties20FO0LQ==2 oԿ_oԿ_Item  Properties UI4EJJ1V==2oԿ_oԿ_Item eProperties(NCX0RBVXCQ==2oԿ_oԿ_Item <Properties>ܱ="08"/> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. cumentation> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. "xsd:string"/> ormDocumentLibraryFormDocumentLibraryForm00Microsof Filter>Document ID GeneratorDocument ID GeneratorSynchronous100011000Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100021001Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100041002Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100061003Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandler ՜.+,D՜.+,`x   @ CAPITAL PLANNING AND MANAGEMENT UT MD ANDERSON CANCER CENTER(e7 Toilet and Bath Accessories Title X<p _dlc_DocId_dlc_DocIdItemGuid_dlc_DocIdUrl Published Date to External SiteReady to PublishStatus