ࡱ> _ Mbjbjzyzy G6b6bDG(((8`<(Am.pp(ssslllllll$on%qFl.!ss.!.!llv(v(v(.!lv(.!lv(v(_jPrlH("jc\lm0Amc kr"krjkrjsrv(\Msssllr%sssAm.!.!.!.!krsssssssssB : SECTION 10 56 26 mobile high density shelving systems GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General Conditions and Division 01 Specification Sections, apply to this Section. Summary Section includes high density, mobile storage filing system. REFERENCE STANDARDS The latest published edition of a reference shall be applicable to this Project unless identified by a specific edition date. Reference amendments adopted prior to the effective date of this Contract shall be applicable to this Project. Materials, installation and workmanship shall comply with all applicable requirements and standards. QUALITY ASSURANCE [DELETE ANY OR ALL OF THE THREE BELOW IF NOT REQUIRED BY SIZE OF JOB.] [ARCHITECT/ENGINEER MUST DELETE EVERYTHING IN BLUE and IN BRACKETS BEFORE PUBLISHING.] Manufacturer Qualifications: Firm (material producer) with not less than five years of production experience, whose published literature clearly indicates general compliance of products with requirements of this section. Installer Qualifications: Firm specializing in high density storage shelving system installation with not less than five years of experience installing systems similar to those required for this Project. Single Source Responsibility: Provide material produced by a single manufacturer for shelving, carriers and track. SUBMITTALS Product Data: Submit manufacturer's specifications to evidence compliance with these specifications. Manufacturer's Product Data shall be clearly and specifically marked to indicate the specific models or types intended for submittals and desired approval. Product Data which is unmarked or unclear as to exact intended submittal will be returned unreviewed to submitter. Shop Drawings: Submit complete shop drawings for each room showing layout of the shelving, track assembly, and structural rails where applicable. Provide dimensioned details of joining, placement of shelving on channel supports, wheel assemblies and elevations of shelving within units. Contract Closeout Submittals: Project Record Documents: Submit in accordance with Section 01770. Operation and Maintenance Data: Submit in accordance with Section 01782. Warranties and Bonds: Submit in accordance with Section 01770. QUALITY ASSURANCE Manufacturer Qualification: All products covered under this Section shall be produced by a single manufacturer unless otherwise specified. Manufacturer shall submit evidence of having not less than five (5) years successful production of this product. Subcontractor Qualifications: Subcontractor shall submit evidence of skill and not less than five (5) years specialized experience with this product. Subcontractor shall be approved by the manufacturer DELIVERY, STORAGE, AND HANDLING Refer to Section016100 Material and Equipment. Deliver, store, and handle products in exact accordance with the manufacturers latest published requirements and specifications. Do not install shelving units until other work in each room is complete, with the exception of finish flooring or other affected finishes. Sequence and scheduling Sequence storage shelving system installation with other Work to minimize possibility of damage and soiling during remainder of construction period. WARRANTY [GENERALLY DELETE THIS ENTIRE ARTICLE. WARRANTIES ARE USUALLY INTENDED ONLY FOR EXTENSIVE CUSTOM FABRICATED WORK OR LARGE HIGH QUALITY INSTALLATIONS WHERE INITIAL COST IS NOT A PRIME FACTOR. IN THE EVENT THAT WARRANTIES ARE REQUIRED, VERIFY WITH OWNER'S COUNSEL THAT WARRANTIES STATED IN THIS ARTICLE ARE NOT LESS THAN WHAT IS AVAILABLE UNDER PREVAILING LOCAL LAWS.] Special Project Warranty: Submit a written warranty, executed by Contractor, Installer and Manufacturer, agreeing to repair or replace units which fail in materials or workmanship within the specified warranty period. This warranty shall be in addition to and not a limitation of other rights the Owner may have against the Contractor under Contract Documents. [IF WARRANTIES ARE REQUIRED, CHANGE THE PARAGRAPH BELOW TO REFLECT THE DESIRED WARRANTY PERIOD.] Warranty period of five (5) years after the date of substantial completion. PRODUCTS GENERAL Materials shall meet or exceed all applicable referenced standards, federal, state and local requirements, and conform to codes and ordinances of authorities having jurisdiction. manufacturers To establish standards of manufacture, operation, performance, and appearance, specifications are based on products of Spacesaver Inc. Subject to compliance with requirements, products of the following manufacturers will also be acceptable: [REVISE MFRS. LISTING TO SUIT AVAILABLE PRODUCTS. VERIFY THE SYSTEM TYPES AVAILABLE FROM EACH MFR. ] Aurora Storage Products Lundia, Inc. Montel, Inc. Mayline Group Spacesaver Corporation Tab Products Co. MATERIALS [configuration OF TRACK, CARRIERS AND METHOD OF MOVEMENT OF SHELF UNITS VARIES WITH MFR. THE TWO MOST COMMON TYPES ARE SPECIFIED BELOW AS EXAMPLES; HIGH DENSITY MOBILE UNIT CARRIER SYSTEM IN WHICH AN ENTIRE BANK OF SHELVES MOVES AT ONCE, AND A LATERALLY MOVING carrier SYSTEM IN WHICH ONLY THE INDIVIDUAL UNITS SLIDE ALONG A TRACK. Mechanically assisted systems, where an entire bank moves, is the type most typically used at md anderson] Mobile High Density Storage System: Mechanically Assisted Mobile System: [select either the type system above or below to suit project requirements. all the detailed information below applies to both type systems, with the exception of items relating to electric motors/controls and mechanical drive] Electrically Operated Mobile System: System with rail and deck assembly, two or more parallel rails, prefabricated platform between rails, and mobilized carrier riding on rails. Unit fastened to floor, and equipped with built in levelers accessible from top surface of deck to be adjusted at any time with system fully loaded and in use Plastic Laminate: NEMA LD 3 high pressure, GP-28 Vertical Grade. Storage Shelf Case: Modular steel storage case equipped with adjustable shelves of height and shelf quantity as indicated. Uprights: Minimum 18 ga. cold rolled steel formed into either a 2 wide Tee shape common post, or a 1 wide Angle shape end post. Locate keyhole-shaped slots at 1 centers vertically on the inner face of posts. Four-post closed uprights shall have a 24 ga. closure panel between the posts, and Case-type uprights shall have two 24 ga. closure panels between the posts and flush with the outer edges of the uprights. All double-face case-type uprights to have a stiffening channel formed along the vertical center line of the closure panel. Adjustable Shelves: 9/16 in height and formed of minimum 22 gage cold-rolled steel with flanges on all four sides and front and rear flanges turned down and in. Shelves to be adjustable on 1 centers vertically, and be supported front and back by two shelf supports of 14 gage min. hot rolled steel. Multi-function slots for file and bin dividers shall be located on 2 centers across entire shelf length, starting 1 from each end. Height of shelf, including supports, shall be . Plain canopy tops shall be supplied on all shelving sections. Shelves shall be designed to carry a minimum load of 50 lbs. per sq. ft. of shelf, with reinforcement as required to provide maximum deflection of 1/8. Construct shelves to lock between uprights and panels. Base and Canopy: Minimum 19 gage steel, fully enclosed base, constructed to receive end and intermediate panels. Canopy of 19 gage steel, with 1 front face. Back Stops and Center Stops: Provide back stops on single-face slotted shelves and center stops on double-face slotted shelves. Back stops shall be minimum 18 gage steel and center stops shall be minimum 24 gage steel. All stops shall be slotted to accept dividers. Dividers: Minimum 20 gage steel dividers and/or bin dividers shall be provided as indicated. Reference Shelves: Waist-high roll out reference shelves shall be provided as indicated. Back Panel: One piece full height steel construction, designed to lock into rear flanges of end and intermediate panels. [security doors below are also applicable to laterally moving carrier systems, and should be included in that section if required in project] Rolling Security Doors: Manually operated, torsion spring assisted aluminum rolling shutters with painted inner and outer faces and center foamed core. Continuous interlocking slats spanning entire door width. Provide sidelocks at ends of alternating slats. Hood constructed of 3005 aluminum alloy, and guide rails constructed of 6063-T5 aluminum. Rails: ASTM/AISI Type 1035 or 1045 steel with a capacity of 1000 pounds per lineal foot and minimum 5/8 inch wide contact surface. Center flanged rails to meet center flanged guide wheels. Assembly recessed within deck to create flush floor. Provide covering for space between rails and platform. Provide manufacturer's design movable carriages fabricated of welded or bolted steel construction. Design carriages to allow shelving uprights to recess and interlock into the carriages a minimum of 3/4 inch (19MM). [tracks MAY BE RECESSED INTO FLOOR IN ORDER TO ELIMINATE CHANGE IN ELEVATION. DELETE DECK item below when RECESSED TRACK is used.] Deck: Minimum 3/4 inch thick, underlayment grade plywood fabricated into panels. Provide factory-produced fire retardant treated material. Cover with finish as indicated. Provide sloped, ADA compliant, aluminum ramp at aisle access side. Carriers: Minimum 11 gage steel channels, fastened together to form rigid frame; continuous lip around entire carriage perimeter, enabling units to be independent of fastening to carrier. Locate channel members to transmit load directly through wheels to rail. Equip each carriage with two rubber bumpers. Height of carriers shall be such that final mounting height for shelving cases is not more than 7 inches above leveled slab. Wheels: Self guiding, center flanged drive wheels to conform to rail profile, turning on steel ball bearings which have been permanently lubricated and sealed. Wheels assembled into steel housing bolted to underside of carrier. Each wheel rated for 3,200 lbs. minimum load capacity. [delete item below if electrically powered system is specified] Mechanical Drive: Provide triple arm operating wheel with rotating hand knobs located on end panel, which transmits power through a chain drive to drive wheels on each carriage. Drive system design shall prevent carriage whipping, binding, and excessive wheel and rail wear. Design gearing system to move a gross load of 4,000 lbs., minimum, with effort of 1 lb. A chain tensioning device shall be provided on each chain drive with provision for adjusting tension without removing end panels. Optional Accessories: Provide accessories as scheduled: [DELETE AS REQUIRED BY PROJECT.] Chrome plated handle for manually movable carriers. Built in drive lock. Built in aisle holder/lock. Anti tip device. Full height end panels to enclose disc drive. Operating handle at each end of carrier. [item below is for a mechanically assisted system] Mechanical, non-powered, sweep and safety stop. [delete option below if electrically powered system is not specified] Mechanical, line powered, sweep and safety stop. Photo sweep scanning and safety stop. Carriage mount locks. Automatic aisle locking system with color-coded indicators for locked or unlocked mode. [items below apply to electrically operated mobile system, and should be deleted if mechanically assisted mobile system is specified] Drive System: Each electric carriage shall be provided with a current limited fractional horsepower gear motor, connected to the drive wheel assembly with a roller chain. System shall operate on 115 V.A.C. 50/60 hertz, 20 amp dedicated circuit, one per module. An overhead mounted power pantogragh distribution system shall conceal all interconnecting wiring. Movement Controls: Carriage control panel on the accessible (open) end of each moveable carriage. Minimum controls shall include directional control buttons, STOP/RESET push-button and a red reset light. System controls shall have the capability to start motors on each movable carriage sequentially to minimize power demands, or all at once as a block. System shall provide smooth operation through dynamic braking. No additional hardware shall be required to change between sequential and block movement. Maximum running speed shall be limited to 3.3 inches (84 mm) per second. Provide solid state controls which include indication of safety system operation status, which aisle is in use, and whether carriages are in locked or unlocked mode. Provide each aisle with a programmable distance sensor to ensure proper timing for start/stop operation. At each aisle, provide full length infrared/photoelectric safety sweep. Safety sweep shall activate to stop carriage movement when an obstruction is detected. Equip with OSHA approved safety demarcation tape. [items below are optional for electrically controlled systems. delete if not required] Provide infrared photoelectric aisle entry sensor system to stop carriage movement if a person entering a closing aisle is detected. Provide sensors at aisle and electric braking devices to prevent new carriage movement if the system detects objects or persons in the open aisle when an attempt is made to open another aisle. Individual Touchpad Aisle Access Controls: Provide a 10-digit push button keypad at each secured carriage, with the capability to reprogram a 4-digit PIN access code. Provide the capability for the motorized shelving system to interface with the buildings fire alarm system or building management system for fire protection. A handheld rechargeable power pack shall be provided for emergency operations in case of primary power failure. [DELETE ENTIRE ARTICLE BELOW IF NO LATERAL SYSTEM IS SPECIFIED.] Laterally Moving Carrier System: Floor mounted stationary carrier platform supporting laterally moving individual shelving case units in front of stationary back row. One guide track, one load track per movable row. Guide Track: Cold finish steel bar positioned in aluminum extrusion. Load Track: 5/8 inch one-piece cold drawn steel, 2-1/8 inch base flange. Deck: Minimum 3/4 inch thick, underlayment grade plywood fabricated into panels and positioned between tracks. Provide factory-produced fire retardant treated material. Cover with finish as indicated. Carriage: One piece notched, welded aluminum extrusion, 5/8 inch lip on all four sides, hollow portion to cover wheels. Wheels: Hardened, precision ground steel, 2-3/4 inch diameter, each equipped with two permanently shielded bearing assemblies. Provide spacers at both sides of wheel bearings to eliminate all friction between wheels and carriage. Stationary Platform: Fixed unit at rear of installation, finished height and construction same as carriage only anchored to track. FINISHES [POSSIBLY LIST FINISH AND COLOR AND DELETE BELOW.] Provide units in finishes and colors as selected by Architect from manufacturer's standard finishes and colors. [DELETE BELOW IF CUSTOM COLOR OR FINISH not REQUIRED.] Provide units in finishes and colors as specified by the Architect for custom finish. EXECUTION [COORDINATE REQUIREMENTS SPECIFIED IN OTHER SECTIONS FOR CONSTRUCTION AND TOLERANCES TO ENSURE THEY ARE APPROPRIATE FOR PRODUCTS SELECTED.] EXAMINATION Examine and verify that receiving substrate surfaces of the structure have no defects or errors which would result in poor or potentially defective application or cause latent defects in workmanship. Report any unsatisfactory conditions to Architect. Starting installation shall imply acceptance of surfaces. PREPARATION Substrate Surface: Prepare substrate surfaces to ensure proper and adequate installation, in exact accordance with the Contract Documents and approved Shop Drawings, or manufacturers requirements. Field Measurements/Verifications: Field measure and verify dimensions are required. Protection of Adjacent Areas or Surfaces: Protect adjacent areas or surfaces from damage as a result of the Work of this Section. INSTALLATION Install high density mobile shelving in accordance with manufacturers latest published requirements and approved shop drawings. Set units in location shown and scheduled, level and plumb each unit, anchor tracking and supports. Concealed fasteners shall be used whenever possible. Ensure operating parts work freely and properly. Damaged Materials: Repair or replace damaged parts having dents, buckles, abrasions, or other damage affecting appearance or serviceability. CLEANING Clean in accordance with Section 01700. Immediately remove all spots, smears, stains, residues, adhesives, etc., from the Work of this Section and/or upon adjacent areas or surfaces which result from the Work of this Section. Upon completion of the Work of this Section, dispose of, away from the Site, all debris, trash, containers, residue, remnants and scraps which result from the Work of this Section. DEMONSTRATION Demonstrate all aspects of the operation of each type of high density moveable shelving to Owners personnel. Furnish complete operating manuals for each type of system. END OF SECTION 10 56 26 FOR MDACC USE ONLY. DELETE THIS PAGE BEFORE ISSUING DOCUMENTS. document revision history IssueDateRevision DescriptionAuthor20190301Original IssuanceRev. 1.Rev. 2Rev. 3 Rev. 4 Rev. 5    MD ANDERSON Project No. XXXXXXMD ANDERSON PROJECT NAMEA/E Name Issue Description A/E Project No.Month 00, 0000 鶹ӳ mobile high density shelving systems MD Anderson Cancer Center10 56 26 MS 20190301 PAGE 3 of  NUMPAGES 10 45OP! " 5 6 # , ] `   7 8 S T ^ ,-fj89ɾۯ͡ hL hhTx h)h) hphW*h+hi~ hhL hhYThL h hL hhD hL hh  h|hW*hW*h<hUt h]x@h]xh`h)?6>P" 6 # 8  T _ m `Tgd mgdmgd|gd|gd mgdm y-:PYa"ygd mgdmgd mgd|gd|9:Paj!"wx6 IJKQRZ[`ab ǿλû÷޻ިިޜh!h|/hDhqh'N+ hN; hN; h|!hN; hUah hL hh0~h0~h|h'Eh2bhChW*h]xh^*y hL hhTxh< hL hhD= a"$%&'Z''a()*+D,2-gd;V!gd|gdmgd|gd mb j ~ !!P!Q!""?"A"S"T"r"x"""##l#s#######($1$:$L$N$j$r$z${$$$$$$$$$$j%t%%%%%%%&&x&~&&&&&&&''Y'Z''(йеhg hOhihLh{hhR2hih{hC h_Bh_Bh_Bh_BCJh1hChC[ch!h_BG( ( ( (((T(_(`(a(1))))*$*%*>*?*y****++,&,+,9,A,C,D,R,U,Z,b,t,u,},,,,,,,,, -G-K-B.J.w.........///¾ºͶͶh:&ho"7hhhDh4fh OhHhh hL hh_h_h7h~Vh h^*yh+AFhC hjhjh9hjh'N+hg h?2-./<0+2c222222(3Q3333+4Q4g44E56y78::1;;  gd;V!gdmgd;V!////<0V011*2c2d22222222(3Q33333+4g4r4w4x444444444E55555I6J6N6d6o666667y78888P8889$9P9ʼʼθhv[h0!8hIh}h#>h hpNh hCh2( h2(h2(h2(h=~hYVhv( hL hhD hL hhTxhhh~DhL7hChS.^hC[c=P9R9g99::1;;;v<w<=====->.>/>m>n>o>>>?????????@@@DAEAHAMABBBBBBB.C/CVCZCcCdCeCCCCODPDQDEEwKϿϻϿϴڴڴڴڴϬڴڴhW* hphW*h]xhUa hL hh h~hkho"7h^*yhxhC hL hhD hL hhTx hh_\h_\h"hvh|h0!8hv[>;<==.>o>>H???@AABBB.CeCCCQD]D%EXEEEEgd mgd|gd mgd|gdmgd;V!EdFFFF:GGGG,HaHHI(IPI JJJ;KwKKKKKgd m$$$d&d1$NPa$gd mgd mgd|gd|gd|gd mwKKKKKL LLLLLLLLLLLLMM M!M4M5M@MAMMMMMMMMMMMMMMMMMMMƾƾƶƶƺƲƮƦƦƦƦh7K>mHnHu*jho"7U*h7K>mHnHujho"7Uh|hmh;V!h{{ho"7B*phho"7h6Ljh6LUh]x h{{5h mh m5h mh m;CJ h mh mh mh+KKK LLLLLLLUkd$$IfTl\,$$0$44 laytG T $Ifgd m LLL!L3L4L\SSSS $Ifgd mkd$$IfTl\,$$0$44 laytG T4L5L6L7L8L9L^UUUU $Ifgd mkd8$$IfTl\,$$0$44 laytG T9L:LALBLDLEL\SSSS $Ifgd mkd$$IfTl\,$$0$44 laytG TELFLGLHLILJL^UUUU $Ifgd mkdp$$IfTl\,$$0$44 laytG TJLKLRLSLTLUL\SSSS $Ifgd mkd $$IfTl\,$$0$44 laytG TULVLWLXLYLZL^UUUU $Ifgd mkd$$IfTl\,$$0$44 laytG TZL[LcLdLeLfL\SSSS $Ifgd mkdB$$IfTl\,$$0$44 laytG TfLgLhLiLjLkL^UUUU $Ifgd mkd$$IfTl\,$$0$44 laytG TkLlLtLuLvLwL\SSSS $Ifgd mkdz$$IfTl\,$$0$44 laytG TwLxLyLzL{L|L^UUUU $Ifgd mkd$$IfTl\,$$0$44 laytG T|L}LLLLL\SSSS $Ifgd mkd$$IfTl\,$$0$44 laytG TLLLLLL^UUUU $Ifgd mkdP$$IfTl\,$$0$44 laytG TLLLLLLLLL\UPPPPPNgdV>gd|kd$$IfTl\,$$0$44 laytG TLLLLLLLLLLLLLLLLLLLLLLLLLLLLgdV>gdTxgd LLLLLLLLLLLLLLLLLLLLLLM $$Ifa$gdV> $IfgdV>gdL hgdV>gdTxgd MM MMM/M>MTH $$Ifa$gd{{Kkd$$IfTH0x$`64 HaT $$Ifa$gdV> $IfgdV>Kkd$$IfTH0x$`64 HaT>M?M@MAMBMCM\MMMHGkd $$IfHU0$ $ $4 Hal $$Ifa$gdV> $IfgdV>gdV>gdL hgdTxKkdF $$IfTH0x$`64 HaTMMMMMMMMMQLGgdL hgdTxGkdg $$IfHU0$ $ &$4 Hal $IfgdmGkd $$IfHU0$ $ $4 Hal $$Ifa$gdV> $IfgdV>MMMgd|E....()()))()000?P&P/R 8$BP/ =!"#8$% Dp$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T$$If!vh#v#v#v#v:V l0$5555ytG T]$$If!vh#v#v`:V H655`44 HT]$$If!vh#v#v`:V H655`44 HT]$$If!vh#v#v`:V H655`44 HT_$$Ifl!vh#v #v:V HU$5 544 Hal_$$Ifl!vh#v #v:V HU$5 544 Halk$$Ifl!vh#v #v:V HU$,5 5944 Hal&s2 0@P`p2( 0@P`p 0@P`p 0@P`p 0@P`p 0@P`p 0@P`p8XV~ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@_HmH nH sH tH J`J cNormal1$OJQJ\]_HmH sH tH ZZ c Heading 1$ <@&^ ;CJKH \^JaJ RR c Heading 2$ P 1$@&^  5;CJXX c Heading 3$ h!  1$@&^ 5;mH sH DA D cDefault Paragraph FontVi@V  Table Normal :V 44 la (k (cNo List P+@P cEndnote Text,EOS$1$a$5;.. cTOC 9 ^P@P cFootnote Text,Foot Title;X1X c Attachment ID$ !xa$ 5;CJR@2R cHeader,Head Project  !;4 B4 cFooter  !>O> mPRT$$ & F1$a$50Ob0 mTITLE5;LOrL |PR1,$ & F ``*$1$@&a$TOrT $|ART0$$ & F `01$^`0a$;POP % mPR2,$ & F *$1$@&a$\>O> cPR3$$ & F1$a$\NON cPR4)$$ & Fp1$^p`a$\NN cPR5)$$ & F 1$^ `a$\<O< m0CMT $1$5;B*phRR cAttachment Name$xa$m$ 5;CJb1b cAttachment,Proj Number h!xx^BB mComment 5;B*CJphHH r Balloon Text!CJOJQJ^JaJ22 nzprsub"^>2> #>PARL1# & F. $1$\]:/A: |ART Char;OJQJ\]4/Q4  mPR2 Char OJQJ]PK![Content_Types].xmlN0EH-J@%ǎǢ|ș$زULTB l,3;rØJB+$G]7O٭Vc:E3v@P~Ds |w< E '19FFFI9b (/P9wKM'*,-/032-;EKL4L9LELJLULZLfLkLwL|LLLLLM>MMM()+.12456789:;<=>?@ABCDEFG%,.3>AI!tt8@0(  B S  ? DDDDGEGEUEEEEEE  DDDDQEZEZEEEEEE  8 *urn:schemas-microsoft-com:office:smarttagsCity=*urn:schemas-microsoft-com:office:smarttags PlaceType=*urn:schemas-microsoft-com:office:smarttags PlaceName9 *urn:schemas-microsoft-com:office:smarttagsplace   -0;!D!d.n.D DDDDDDDDDDDDEEEEEEDDDDDDDDDDDEE33"#,T aj5577221:LNz{y y 3!3!c!c!!!@"@"z"z"J#J#$$$$%%w&&((O)O)))S-S-00P2P24477Q<wCCDDDDDDDDDDDDDDDDDDDEE E!E4E5E?EBEEEEEEEEEEE"#,T aj5577221:LNz{y y 3!3!c!c!!!@"@"z"z"J#J#$$$$%%w&&((O)O)))S-S-00P2P24477Q<wCCDDDDDDDDDDDDDDDDDDDDEE E!E4E5E?E@EAEAEBEEEEEEEEEEEEE+|})S~>B#Ǥʢ4y$*:Y/s Kc &r/&L%&H%.X&c}'&Jk3/-ho2ي+#27H5jc217t< <&,=qRa@,l@ALk#_ELZdB.L&VTQf=Tsz*F\ `|b&kkn|smJX [oLmszgB {w Qpx:4^`.^`.88^8`.^`. ^`OJQJo( ^`OJQJo( 88^8`OJQJo( ^`OJQJo(hh^h`. hh^h`OJQJo(^`o( PART - ^`o( SCHEDULE  - ^`o(PRODUCT DATA SHEET  - ``^``o(.``^``o(.^`o(.^`o(.  ^ `o()` ` ^` `o()@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.^`o(.^`.pLp^p`L.@ @ ^@ `.^`.L^`L.^`.^`.PLP^P`L.88^`5CJOJQJ\^JaJh.@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.^`o(.^`o(.^`o(.^`o(.pLp^p`L.@ @ ^@ `.^`.L^`L.^`.^`.PLP^P`L.^`o(.^`o(.^`o(.ww^w`o(ww^w`o(.0^`0o(..0^`0o(... 88^8`o( .... 88^8`o( ..... 88^8`o( ...... `^``o(....... `^``o(........^`o(.^`o(.h^h`o(^`o(.@ 0^@ `0o(..x0^x`0o(... ^`o( .... P^P`o( ..... `^``o( ...... (#`^(#``o(....... (^(`o(........@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.^`o(^`o(.^`o(..^`o(... ^`o( .... ^`o( ..... ^`o( ...... `^``o(....... `^``o(........^`o(.@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.^`o(.{^`{o(2.03  ^ `o(..  ^ `o(...   ^ `o( ....   ^ `o( .....   ^ `o( ......  ` ^ ``o(.......  ` ^ ``o(........ww^w`o(ww^w`o(.0^`0o(..0^`0o(... 88^8`o( .... 88^8`o( ..... 88^8`o( ...... `^``o(....... `^``o(........^`o(^`o(.^`o(..^`o(... ^`o( .... ^`o( ..... `^``o( ...... `^``o(....... `^``o(........^`o(.^`o(.{^`{o(3.  ^ `o(..  ^ `o(...   ^ `o( ....   ^ `o( .....   ^ `o( ......  ` ^ ``o(.......  ` ^ ``o(........^`o(.^`o(.^`o(.^`o(^`o(.0^`0o(..0^`0o(... 88^8`o( .... 88^8`o( ..... 88^8`o( ...... `^``o(....... `^``o(........@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.@^`o(.@^`.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L. ww^w`o(hH ww^w`o(hH. 0^`0o(hH. 0^`0o(hH... 88^8`o(hH .... 88^8`o(hH ..... 88^8`o(hH ......  `^``o(hH.......  `^``o(hH........^`o(.@^`o(.^`o(.@pLp^p`L.@@ @ ^@ `.@^`.@L^`L.@^`.@^`.@PLP^P`L.-<<Kc `|b <r/.L#_Ec}'kka@o2VT*F\#2=TB {wH% [o217E pxsm,=4yJk3/msl@A ~}|L%7H5R<0++&        ي+        &        5 /       &         Q        &        &        &h       .nziIN; G #> OOO|!<j!g V!;V!:&@a&(v(+'N+9p++,3-;-J/|/937o"7L70!8y-97K>V>~?xAC'E+AF:JyK\YNpNF:PmQ5vR~V_ \_\N ]W^S.^ `e`UacC[c/seze4fL hThkpkd;ov~onZpdrUtCwMxx]x+y^*yd7|' }}=~i~6L~{AGa-9{1b2(8v4~~DTxq_PA@ H|`i2|=9P1R|~2b'"W*R2YT{{o ~mhh)1 v[f>HDL_BYV m HjnD7y0~r0=WrL.C~!t4DD@E@UnknownG.[x Times New Roman5Symbol3. .Cx Arial5. .[`)TahomaA$BCambria Math"9@)hPE'tc& ; T: #|; T: #|%)P4lDlD2Q)PHP ?H2!xx WC:\Documents and Settings\JRCollins\Application Data\Microsoft\Templates\CSI_STYLES.dot#Mobile High Density Shelving SystemFitzgerald,Richard W+                           ! " # $ % & ' ( ) * Oh+'0L     ,4<D$Mobile High Density Shelving SystemALTERATION OF THIS OFFICIAL DOCUMENT IS PROHIBITED WITHOUT EXPRESS WRITTEN PERMISSION BY OFFICE OF CAPITAL PLANNING AND MANAGEMENT AT UT MD ANDERSON CANCER CENTER. CSI_STYLESFitzgerald,Richard W10Microsoft Office Word@02+@[q@0(@5gH ; T:us CSI Division SZWXXFYDWACR-487-693%ba66e368-53db-4c92-8efa-bc8a166b3073thttp://fm/groups/cpm/TRG/o ?@ABCDEFGHJKLMNOPRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~Root Entry Fp}_Data I1TableQ#sWordDocumentGSummaryInformation(DocumentSummaryInformation8,LCompObjrMsoDataStore z_p}_  !"#$%&')*+-./0123456789:;B=?@ACDEFG  F Microsoft Word 97-2003 Document MSWordDocWord.Document.89q DocumentLibraryF5VULNYOQQ==2 z_z_Item  x.PropertiesA1M324PNTQ==2 z_p}_Item  Properties U54UVL1ECFA==2z_p}_Item eProperties(HWKGVCOMAKQA==2z_p}_Item <Properties>ܱ="08"/> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. cumentation> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. "xsd:string"/> ormDocumentLibraryFormDocumentLibraryForm00Microsof Filter>Document ID GeneratorDocument ID GeneratorSynchronous100011000Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100021001Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100041002Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100061003Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandler ՜.+,D՜.+,hx   H CAPITAL PLANNING AND MANAGEMENT UT MD ANDERSON CANCER CENTERF|#lD $Mobile High Density Shelving System Title X<p _dlc_DocId_dlc_DocIdItemGuid_dlc_DocIdUrl Published Date to External SiteReady to PublishStat