ࡱ> _ vbjbjzyzy >6b6bmzz   8BL 70rr(u u u 7777777$8;?7V#u u V#V#?7T72*2*2*V#72*V#72*2*n36m$$B4 7j7074f=.&f=@66&f=6\u #!|2*!d"Su u u ?7?7( u u u 7V#V#V#V#f=u u u u u u u u u zB : SECTION 12 93 00 SITE AND STREET FURNISHINGS GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. SUMMARY This Section includes the following site and street furnishings: ADJUST LIST BELOW TO SUIT PROJECT. Benches. Ganged seats. Bicycle racks. Trash receptacles. SUBMITTALS Product Data: For each type of product indicated. Include construction details, material descriptions, dimensions of individual components and profiles, finishes, field-assembly requirements, and installation details. Samples for Verification: For each type of exposed finish required, prepared on Samples of size indicated below. Size: Not less than 6-inch-(150-mm-) long linear components and 4-inch-(100-mm-) square sheet components. USUALLY RETAIN SUBPARAGRAPH ABOVE. RETAIN SUBPARAGRAPH BELOW IF CRITICAL FOR PROJECT AND PRODUCT. Full Size: [Bench] [Ganged seating] [Bicycle rack] [Trash receptacle]. Product Schedule: For site and street furnishings. Use same designations indicated on Drawings. Material Certificates: For site and street furnishings, signed by manufacturers. EDIT SUBPARAGRAPHS BELOW TO SUIT PROJECT. Wood Preservative Treatment: Include certification by treating plant stating type of preservative solution and pressure process used, net amount of preservative retained, and compliance with applicable standards. Sustainably Harvested Wood: Include certification by manufacturer and from sources that participate in sustained yield programs. Recycled plastic. Maintenance Data: For site and street furnishings to include in maintenance manuals. QUALITY ASSURANCE Source Limitations: Obtain each type of site and street furnishings through one source from a single manufacturer. PRODUCTS MANUFACTURERS Products: Subject to compliance with requirements, provide one of the following: Benches: Ganged Seats: Bicycle Racks: Trash Receptacles: MATERIALS Aluminum: Alloy and temper recommended by aluminum producer and finisher for type of use and finish indicated; free from surface blemishes and complying with the following: Rolled or Cold-Finished Bars, Rods, and Wire: ASTMB211(ASTMB211M). Extruded Bars, Rods, Wire, Profiles, and Tubes: ASTMB221(ASTMB221M). Structural Pipe and Tube: ASTMB429. Sheet and Plate: ASTMB209(ASTMB209M). Steel: Free from surface blemishes and complying with the following: Plates, Shapes, and Bars: ASTMA36/A36M. Steel Pipe: Standard-weight steel pipe complying with ASTMA53, or electric-resistance-welded pipe complying with ASTMA135. Tubing: Cold-formed steel tubing complying with ASTMA500. Mechanical Tubing: Cold-rolled, electric-resistance-welded carbon or alloy steel tubing complying with ASTMA513, or steel tubing fabricated from steel complying with ASTMA569/A569M and complying with dimensional tolerances in ASTMA500; zinc coated internally and externally. Sheet: Commercial steel sheet complying with ASTMA569/A569M. Perforated Metal: From steel sheet not less than [0.0747-inch(1.9-mm)] [0.0897-inch(2.3-mm)] [0.1196-inch(3.0-mm)] nominal thickness; manufacturer's standard perforation pattern. REVISE SUBPARAGRAPH ABOVE IF SPECIFIC PATTERN IS CRITICAL FOR PROJECT; REVISE SUBPARAGRAPH BELOW IF SPECIFIC DESIGNATION IS CRITICAL. Expanded Metal: From carbon-steel sheets, deburred after expansion, and complying with ASTMF1267. Stainless Steel: Free from surface blemishes and complying with the following: Sheet, Strip, Plate, and Flat Bars: ASTMA666. Pipe: Schedule40 steel pipe complying with ASTMA312/A312M. Tubing: ASTMA554. Wood: Surfaced smooth on four sides with eased edges; kiln dried, free of knots, solid stock of species indicated. RETAIN 1 OF 12 EXAMPLE SUBPARAGRAPHS AND ASSOCIATED SUBPARAGRAPHS BELOW OR REVISE TO SUIT PRODUCT. Douglas Fir: Clear grade, vertical grain. Finish: Manufacturer's standard [stain] [and] [transparent sealer] [transparent wood preservative treatment and sealer] . Pine: Southern pine; No.2 or better; SPIB. Preservative treated with [CCA 0.40-lb/cu. ft.(6.4-kg/cu. m) minimum retention according to AWPAC2 or AWPAC17] . Kiln dried after treatment. GENERALLY DELETE SUBPARAGRAPH ABOVE IF OPTION FOR PRESERVATIVE TREATMENT IS INSERTED IN SUBPARAGRAPH BELOW. CCA PRESERVATIVE TREATMENT IS PRIMARILY USED BY THOSE MANUFACTURERS THAT ALSO MANUFACTURE PUBLIC PARK AND PLAYGROUND EQUIPMENT. Finish: Manufacturer's standard [stain] [and] [transparent sealer] [transparent wood preservative treatment and sealer] . DELETE ALL SUBPARAGRAPHS ABOVE AND RETAIN APPLICABLE SUBPARAGRAPH BELOW IF PRESERVATIVE-TREATED WOOD SPECIES ARE UNACCEPTABLE OR NATURALLY ROT-RESISTANT SPECIES ARE REQUIRED FOR PROJECT. MANUFACTURERS MAY APPLY SEALERS AND COLORANTS FOR DURABILITY OR IF REQUIRED FOR LOCAL CLIMATES. INSERT APPLICABLE TREATMENTS BELOW. [Eastern White] [Red] [Yellow]Cedar: Select grade or better. Redwood: [Clear all heart] [Construction heart or better,] free-of-heart center; RIS. RETAINING OPTION IN FIRST SUBPARAGRAPH BELOW RISKS SPECIFYING A PROPRIETARY PRODUCT. CURRENTLY, TEAK FROM SMITH & HAWKEN IS THE ONLY WOOD PROVIDED BY MANUFACTURERS LISTED IN THE EVALUATIONS THAT HAS THIRD-PARTY CERTIFICATION. TEAK FROM SMITH & HAWKEN IS CERTIFIED BY SMARTWOOD, WHICH IS ACCREDITED BY THE FOREST STEWARDSHIP COUNCIL. Teak (Tectona Grandis): Clear grade.[Provide wood, obtained from sources that participate in a well-managed forest and chain-of-custody program certified by an independent agency accredited by the Forest Stewardship Council (FSC).] Mahogany (Swietenia Spp): Clear grade. Ipe (Tabebuia Spp): Clear grade. Jarrah (Eucalyptus Marginata): Select grade or better. Jatoba (Hymenaea Courbaril): Clear grade. Pau Lope: Purpleheart (Peltogyne Spp): Clear grade. : . Anchors, Fasteners, Fittings, and Hardware: [Stainless steel] [Brass] [Galvanized steel] [Zinc-plated steel] [Manufacturer's standard, corrosion-resistant-coated or noncorrodible materials]; commercial quality; [tamperproof, vandal and theft resistant;] concealed, recessed, and capped or plugged. Provide as required for site and street furnishings' assembly, mounting, and secure attachment. Angle Anchors: For inconspicuously bolting legs of site and street furnishings to [on-grade] [below-grade] substrate; [one per leg] [extent as indicated on Drawings] . USUALLY RETAIN SUBPARAGRAPH ABOVE OR BELOW. IF BOTH TYPES OF ANCHORAGE SUIT PROJECT, RETAIN BOTH AND INDICATE LOCATIONS ON DRAWINGS. Antitheft Hold-Down Brackets: For securing site and street furnishings to substrate; [two per unit] [extent as indicated on Drawings] . Nonshrink, Nonmetallic Grout: Premixed, factory-packaged, nonstaining, noncorrosive, nongaseous grout complying with ASTMC1107. Provide grout, recommended in writing by manufacturer, for exterior applications. RETAIN PARAGRAPH ABOVE OR BELOW IF SITE AND STREET FURNISHINGS ARE SET IN PIPE SLEEVES OR VOIDS IN CONCRETE; OTHERWISE, DELETE BOTH. Erosion-Resistant Anchoring Cement: Factory-packaged, nonshrink, nonstaining, hydraulic-controlled expansion cement formulation for mixing with potable water at Project site to create pourable anchoring, patching, and grouting compound. Provide formulation that is resistant to erosion from water exposure without needing protection by a sealer or waterproof coating and that is recommended in writing by manufacturer for exterior applications. DELETE PARAGRAPH AND SUBPARAGRAPHS BELOW IF FERROUS COMPONENTS OF SITE AND STREET FURNISHINGS ARE NOT GALVANIZED OR IF NO FERROUS COMPONENTS. Galvanizing: Where indicated for steel and iron components, provide the following protective zinc coating applied to components after fabrication: Zinc-Coated Tubing: External, zinc with organic overcoat, consisting of a minimum of 0.9 oz./sq. ft.(0.27 kg/sq. m) of zinc after welding, a chromate conversion coating, and a clear, polymer film. Internal, same as external or consisting of 81 percent, not less than 0.3-mil-(0.0076-mm-) thick, zinc pigmented coating. Hot-Dip Galvanizing: According to ASTMA123/A123M, ASTM A153/A153M, or ASTMA924/A924M. [BENCHES] [GANGED SEATS] Frame: [Cast aluminum] [Cast iron] [Steel] [Stainless steel] [Wrought iron] [Teak] [Mahogany] . RETAIN ONE OF FIRST THREE PARAGRAPHS BELOW. IF SIZES OF COMPONENTS ARE CRITICAL AND NOT INDICATED ON DRAWINGS, REVISE RETAINED PARAGRAPH BY ADDING SIZES AND DIMENSIONS TO SUIT PROJECT AND PRODUCT. [Stainless-]Steel Seat[and Back]: Fabricated from [perforated metal] [expanded metal] [evenly spaced, parallel flat straps or bars] [evenly woven, flat straps or bars] [edge framed, evenly spaced, parallel rods or rolled bars] [evenly spaced parallel tubing] [grid in tubular frame] . Wood Seat[and Back]: [Douglas fir] [Pine] [Cedar] [Redwood] [Teak] [Mahogany] [Ipe] [Jarrah] [Jatoba] [Pau lope] [Purpleheart] ; formed from [evenly spaced parallel slats] [planks] . Seat[and Back]: [Fiberglass] [Plastic]; formed from [solid piece] [perforated sheet] [evenly spaced parallel slats] [planks] . Arms: [None] [One, as indicated on Drawings] [Two, at each end] [Three, at each end and center] . Arm Material: Match [frame] [seat] . DELETE PARAGRAPH ABOVE AND FIRST PARAGRAPH BELOW IF BENCH HAS NO ARMS. IF ABOVE IS RETAINED AND SIZES OF COMPONENTS ARE CRITICAL AND NOT INDICATED ON DRAWINGS, REVISE TO SUIT PROJECT AND PRODUCT. Arm Height: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . Seat Height: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . IF BENCH HAS NO BACK, AND ARM OR SEAT IS HIGHEST ELEMENT, RETAIN ONE OF TWO, OR BOTH, PARAGRAPHS ABOVE, AS APPLICABLE, OR RETAIN FIRST PARAGRAPH BELOW; RETAINING BOTH WOULD BE REPETITIVE. Overall Height: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . Overall Width: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . Overall Depth: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . CONSIDER RETAINING FIRST PARAGRAPH BELOW TO HELP SPECIFY QUALITY. WHEN COMPARING SIMILAR PRODUCTS MADE FROM THE SAME MATERIALS, HEAVIER UNITS OFTEN PROVIDE BETTER QUALITY. SEE EVALUATIONS. Weight: Seat Surface Shape: [Flat] [Contoured or dished]. Unit Configuration: [Straight] [Angled] [Curved concave to radius indicated on Drawings] [Curved convex to radius indicated on Drawings] [As indicated on Drawings]. RETAIN FIRST PARAGRAPH BELOW OR REVISE TO SUIT PROJECT; DELETE IF NOT APPLICABLE. Assembled Configuration: Units forming closed [hexagon] [octagon] [circle] [oval] [shape indicated on Drawings] and wrapping around a central [tree trunk] [planter] [light post] . Installation Method: [Anchored at finished grade to substrate indicated on Drawings] [Anchored below finished grade to substrate indicated on Drawings] [Cast in concrete] [Attached to sleeve that is cast in concrete] [Wall mounted] [Top of wall mounted] [As indicated on Drawings]. RETAIN ANY OR ALL OF SIX PARAGRAPHS AND ASSOCIATED SUBPARAGRAPHS BELOW TO SUIT PROJECT AND PRODUCT. Aluminum Finish: [Mill finish] [Color coated]. DELETE SUBPARAGRAPH BELOW IF ALUMINUM IS MILL FINISHED. Color: [As indicated by manufacturer's designation] [Match Architect's samples] [As selected by Architect from manufacturer's full range] [As indicated on a site and street furnishing schedule] . Steel Finish: [Galvanized and] [color coated] [PVC-color coated]. Color: [As indicated by manufacturer's designation] [Match Architect's samples] [As selected by Architect from manufacturer's full range] [As indicated on a site and street furnishing schedule] . Stainless-Steel Finish: [Satin, Directional Polish No.6] . Wood Finish: [Unfinished] [Factory-applied transparent finish] [Factory-applied stain and transparent finish] [Factory-applied opaque finish] [Manufacturer's standard finish]. RETAIN SUBPARAGRAPH BELOW IF RETAINING OPTION FOR STAIN AND TRANSPARENT FINISH IN PARAGRAPH ABOVE. Stain: [Manufacturer's standard] . Graphics: [Surface-applied] [Engraved] [Attached brass plaque with engraved] copy, content, and style [per manufacturer's standard] [as indicated on Drawings]. BICYCLE RACKS Frame: [Aluminum] [Steel] [Galvanized steel] [Stainless steel] [Steel and redwood] [Steel and pine] . RETAIN EXAMPLE SUBPARAGRAPHS BELOW OR REVISE TO SUIT PRODUCT. NOT ALL BICYCLE RACKS ARE MADE FROM PIPE OR TUBING AND SOLID BARS. MOST MANUFACTURERS RECOMMEND SCHEDULE40 PIPE, COMPLYING WITH ASTMA53, FOR HEAVY-DUTY APPLICATIONS. FOR SOME PRODUCTS, DEPENDING ON STYLE, E.G., SERPENTINE, PIPE DIAMETERS AND WALL THICKNESSES OF STANDARD AND HEAVY-DUTY RACKS MAY DIFFER. [Pipe] [Tubing]OD: Not less than [1-5/8 inches(41 mm)] [2-3/8 inches(60 mm)] [2-7/8 inches(73 mm)] [4-1/2 inches(115 mm)] . Locking Bars: Solid round bar, not less than [3/4 inch(19 mm)] [1 inch(25 mm)] in diameter. Style: [Traditional, single-side parking] [Traditional, double-side parking] [Arched loop] [Serpentine or ribbon] [Concentric coil or spiral] [Bollard] [Wall-mounted hook] [Wall-mounted loop] [As indicated on Drawings] . Overall Height: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . Overall Width: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . Overall Depth: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . Capacity: Designed to accommodate not less than [two] [three] [four] [five] [seven] [eight] [nine] [11] [12] [13] bicycles. Security: Designed to lock [wheel] [and] [frame]. DELETE FIRST PARAGRAPH BELOW IF NO ACCESSORIES. Accessories: [Base covers for each pipe and tubing anchored end] [Wheel stops]. Installation Method: [Freestanding] [Surface flange anchored at finished grade to substrate indicated on Drawings] [Surface flange anchored below finished grade to substrate indicated on Drawings] [Cast in concrete] [Bolted to cast-in anchor bolts] [Wall mounted] [As indicated on Drawings]. RETAIN ONE OF FOUR PARAGRAPHS AND ASSOCIATED SUBPARAGRAPHS BELOW. Aluminum Finish: [Mill finish] [Color coated]. DELETE SUBPARAGRAPH BELOW IF ALUMINUM IS MILL FINISHED. Color: [As indicated by manufacturer's designation] [Match Architect's samples] [As selected by Architect from manufacturer's full range] [As indicated on a site and street furnishing schedule] . Steel Finish: [Galvanized] [Color coated]. DELETE SUBPARAGRAPH BELOW IF GALVANIZED COATING IS FINAL FINISH. Color: [As indicated by manufacturer's designation] [Match Architect's samples] [As selected by Architect from manufacturer's full range] [As indicated on a site and street furnishing schedule] . Stainless-Steel Finish: [Satin No.4] . DELETE PARAGRAPH ABOVE IF NO STAINLESS STEEL AND BELOW IF NO WOOD COMPONENTS. Wood Finish: [Unfinished] [Manufacturer's standard finish]. TRASH RECEPTACLES RETAIN ONE OF FIRST FIVE PARAGRAPHS BELOW. Aluminum Facing Surrounds: [Aluminum sheet] [Perforated aluminum sheet] [Grid in tubular frame] [Evenly patterned, parallel flat steel straps, bars, or tubular shapes] [Match benches] . [Stainless-]Steel Facing Surrounds: [Steel sheet] [Perforated steel sheet] [Evenly patterned, parallel flat steel straps, bars, or tubular shapes] [Evenly patterned, parallel round steel rods, bars, or tubular shapes] [Grid in tubular frame] [Match benches] . Wood Facing Surrounds: [Evenly spaced, Douglas fir slats] [Evenly spaced pine slats] [Evenly spaced cedar slats] [Redwood panels] [Evenly spaced redwood slats] [Teak panels] [Evenly spaced teak slats] [Evenly spaced mahogany slats] [Evenly spaced ipe slats] [Evenly spaced jatoba slats] [Evenly spaced jarrah slats] [Evenly spaced, pau lope slats] [Evenly spaced purpleheart slats] [Match benches] . DELETE FIRST PARAGRAPH BELOW IF NO SUPPORTING FRAME. DESIGNS WITH SLATTED FACING SURROUNDS AND OTHER REPEATING PARALLEL MEMBERS TYPICALLY REQUIRE SUPPORT FRAMING; SHEET OR MOLDED MATERIALS MAY NOT. Support Frames: [Steel] [Galvanized steel]; welded. Receptacle Shape, Form, and Function: [Round cylinder] [Round cylinder with tapered funnel top] [Round, tapered column] [Square column] [Rectangular column] [As indicated on Drawings] ; with opening[s] for depositing trash in [lid or top] [side of lid or top] [receptacle side]. Lids and Tops: [Matching facing panels] [Aluminum] [Steel] [HDPE] [Recycled HDPE] secured by cable or chain, hinged, swivelled, or permanently secured. Description: [Flat rim ring lid with center opening] [Dome top] [Arched top] [Elevated flat or shallow dome rain cap lid] . DELETE PARAGRAPH AND SUBPARAGRAPH ABOVE IF UNCOVERED TOP SUITS PROJECT. DELETE SUBPARAGRAPH BELOW IF OPENINGS ARE NOT COVERED BY FLAPS. Flap[s]: Opening[s] for depositing trash covered by [self-closing, spring-loaded-hinged, push-in] [rotating] weather flap. DELETE FIRST PARAGRAPH BELOW IF NOT APPLICABLE OR REVISE TO SUIT PROJECT AND PRODUCT. Style: [To match benches] [As indicated by manufacturer's designation]. Overall Height: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . Overall Diameter: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . RETAIN PARAGRAPH ABOVE IF RECEPTACLE SHAPE IS ROUND OR TWO PARAGRAPHS BELOW IF RECEPTACLE SHAPE IS SQUARE OR RECTANGULAR. Overall Width: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . Overall Depth: [As indicated on Drawings] [As indicated in a site and street furnishing schedule] . CONSIDER RETAINING FIRST PARAGRAPH BELOW TO HELP SPECIFY QUALITY. WHEN COMPARING SIMILAR PRODUCTS MADE FROM THE SAME MATERIALS, HEAVIER UNITS OFTEN PROVIDE BETTER QUALITY. SEE EVALUATIONS. Weight: Inner Container: [Aluminum] [Galvanized steel sheet] [Perforated metal] [Fiberglass] [Rigid plastic] container [with drain holes] [with lift-out handles] designed to be removable and reusable. RETAIN PARAGRAPH ABOVE OR FIRST PARAGRAPH BELOW, OR BOTH, TO SUIT PROJECT AND PRODUCT. Disposable Liners: Provide receptacle designed to accommodate disposable liners. Capacity: Not less than [22 gal.(83 L)] [28 gal.(106 L)] [30 gal.(114 L)] [32 gal.(121 L)] [40 gal.(151 L)] [55 gal.(208 L)] . Service Access: [Removable lid or top] [Fixed lid or top, side access], inner container and disposable liner lift or slide out for emptying[; lockable with padlock hasps] [; keyed lock with two keys per receptacle] [; self-latching hinge]. Installation Method: [Freestanding] [Freestanding with weighted base] [Anchored to substrate indicated on Drawings] [Wall mounted] [Post mounted] [Mounted on elevated leg angles anchored at finished grade to substrate indicated on Drawings] [Mounted on elevated leg angles anchored below finished grade to substrate indicated on Drawings] [As indicated on Drawings]. RETAIN SUBPARAGRAPH BELOW FOR POST-MOUNTED APPLICATIONS. Post Mount: [Color-coated steel pipe; color to match receptacle] [Galvanized steel pipe] [Wood]; for mounting [one] [two] [three] receptacle[s]. RETAIN ANY OR ALL OF SIX PARAGRAPHS AND ASSOCIATED SUBPARAGRAPHS BELOW TO SUIT PROJECT AND PRODUCT. Aluminum Finish: Color coated. Color: [As indicated by manufacturer's designation] [Match Architect's samples] [As selected by Architect from manufacturer's full range] [As indicated on a site and street furnishing schedule] . Steel Finish: [Galvanized and] [color coated] [PVC-color coated]. Color: [As indicated by manufacturer's designation] [Match Architect's samples] [As selected by Architect from manufacturer's full range] [As indicated on a site and street furnishing schedule] . Stainless-Steel Finish: [Satin, Directional Polish No.6] . Wood Finish: [Unfinished] [Factory-applied transparent finish] [Factory-applied stained and transparent finish]. Stain: DELETE PARAGRAPH AND SUBPARAGRAPH BELOW IF NO GRAPHICS. Graphics: [Surface-applied] [Engraved] content and style [per manufacturer's standard] [as indicated on Drawings]. Copy: [Litter] [Trash] [Waste]. FABRICATION Metal Components: Form to required shapes and sizes with true, consistent curves, lines, and angles. Separate metals from dissimilar materials to prevent electrolytic action. Welded Connections: Weld connections continuously. Weld solid members with full-length, full-penetration welds and hollow members with full-circumference welds. At exposed connections, finish surfaces smooth and blended so no roughness or unevenness shows after finishing and welded surface matches contours of adjoining surfaces. Pipes and Tubes: Form simple and compound curves by bending members in jigs to produce uniform curvature for each repetitive configuration required; maintain cylindrical cross section of member throughout entire bend without buckling, twisting, cracking, or otherwise deforming exposed surfaces of handrail and railing components. Steel and Iron Components: Galvanized, galvanized and color coated, or color coated. Bare metal steel or iron components are not permitted. Preservative-Treated Wood Components: Complete fabrication of treated items before treatment if possible. If cut after treatment, apply field treatment complying with AWPAM4 to cut surfaces. Exposed Surfaces: Polished, sanded, or otherwise finished; smooth all surfaces, free from burrs, barbs, splinters, and sharpness; all edges and ends rolled, rounded, or capped. Factory Assembly: Assemble components in the factory to the greatest extent possible to minimize field assembly. Clearly mark units for assembly in the field. FINISHES, GENERAL Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for recommendations for applying and designating finishes. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in the same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. ALUMINUM FINISHES REVISE PARAGRAPH BELOW IF LESS-DURABLE, NON-POWDER-COAT, BAKED-ENAMEL FINISH SUITS PROJECT AND PRODUCT. MOST MANUFACTURERS LISTED IN THE EVALUATIONS FINISH PRODUCTS WITH BAKED, POLYESTER-TGIC, POWDER-COAT FINISH. VERIFY FINISH WITH MANUFACTURERS. Baked-Enamel, Powder-Coat Finish: Manufacturer's standard, baked, polyester-TGIC, powder-coat finish complying with finish manufacturer's written instructions for surface preparation, including pretreatment, application, baking, and minimum dry film thickness. STEEL AND GALVANIZED STEEL FINISHES REVISE PARAGRAPH BELOW IF LESS-DURABLE, NON-POWDER-COAT, BAKED-ENAMEL FINISH SUITS PROJECT AND PRODUCT. MOST MANUFACTURERS LISTED IN THE EVALUATIONS FINISH PRODUCTS WITH BAKED, POLYESTER-TGIC, POWDER-COAT FINISH. VERIFY FINISH WITH MANUFACTURERS. Baked-Enamel, Powder-Coat Finish: Manufacturer's standard, baked, polyester-TGIC, powder-coat finish complying with finish manufacturer's written instructions for surface preparation, including pretreatment, application, baking, and minimum dry film thickness. STAINLESS-STEEL FINISHES Remove tool and die marks and stretch lines or blend into finish. EXECUTION EXAMINATION Examine areas and conditions, with Installer present, for compliance with requirements for correct and level finished grade, mounting surfaces, installation tolerances, and other conditions affecting performance. Proceed with installation only after unsatisfactory conditions have been corrected. INSTALLATION, GENERAL Comply with manufacturer's written installation instructions, unless more stringent requirements are indicated. Complete field assembly of site and street furnishings, where required. Unless otherwise indicated, install site and street furnishings after landscaping and paving have been completed. Install site and street furnishings level, plumb, true, and [securely anchored] [positioned] at locations indicated on Drawings. RETAIN ONE OF TWO PARAGRAPHS BELOW IF SITE AND STREET FURNISHINGS ARE SUPPORTED BY EMBEDDED PIPE OR TUBING POSTS, OR REVISE TO SUIT PROJECT. Post Setting: Set cast-in support posts in concrete footing with smooth top, shaped to shed water. Protect portion of posts above footing from concrete splatter. Verify that posts are set plumb or at correct angle and are aligned and at correct height and spacing. Hold posts in position during placement and finishing operations until concrete is sufficiently cured. Posts Set into Voids in Concrete: Form or core-drill holes for installing posts in concrete to depth recommended in writing by manufacturer of site and street furnishings and 3/4 inch(20 mm) larger than OD of post. Clean holes of loose material, insert posts, and fill annular space between post and concrete with [nonshrink, nonmetallic grout] [or] [anchoring cement], mixed and placed to comply with anchoring material manufacturer's written instructions, with top smoothed and shaped to shed water. RETAIN BELOW IF SITE AND STREET FURNISHINGS ARE INSTALLED IN PIPE SLEEVES. Pipe Sleeves: Use steel pipe sleeves preset and anchored into concrete for installing posts. After posts have been inserted into sleeves, fill annular space between post and sleeve with [nonshrink, nonmetallic grout] [or] [anchoring cement], mixed and placed to comply with anchoring material manufacturer's written instructions, with top smoothed and shaped to shed water. CLEANING After completing site and street furnishing installation, inspect components. Remove spots, dirt, and debris. Repair damaged finishes to match original finish or replace component. END OF SECTION 12 93 00 FOR MDACC USE ONLY. DELETE THIS PAGE BEFORE ISSUING DOCUMENTS. document revision history IssueDateRevision DescriptionAuthor20190301Original IssuanceRev. 1.Rev. 2Rev. 3 Rev. 4 Rev. 5      MD ANDERSON Project No. XXXXXXMD ANDERSON PROJECT NAMEA/E NameIssue DescriptionA/E Project No.Month 00, 0000 鶹ӳ SITE AND STREET FURNISHINGSMD Anderson Cancer Center12 93 00 MS 20190301 PAGE 13 of  NUMPAGES 13 -5FG/ Q [ % , 5 N O AB'J\ MWdtvͼͼh%Fh+~h(5hih(0J$B*phhih(0J%B*phh( hih( hihi hiNH hi@ h|h( h+~h(hi hO3,h(>-5G/ R [ i x r O \ gdi#gdZgdigdi$ `*$@& gdi `0*$@& ^`0gdigdigdZ 0B'5L[&f  & Fgd%Fgd%Fgdigdigdigdi*C GxBg6#Y& gd%Fgdi#gdZgdi  & Fgdiv  GxBGJd6"#EJMPSeh  <WdsvD ̶̶̶̶̶̶̶̶̶̶̶̶̶̶̶̶̶̶̶̾h+~h(5 hh( hihi h+~h(hih(5 hih(hih(0J$5B*phhih(0J%5B*phH $ P k !2!M![!v!!!!!!""5"$ $#$.$<$G$J$i$l$y$|$%%Y%e%h%%%%p&&&(A)B)),*;*J*****),,,,0104080;0J0M011122 44444555hh(0J.hih(0J$B*phhih(0J%B*ph hih( hihi h+~h(h+~h(5K& m !O!x!!8"#|$%%p&&(B))+v++),,". //0gdi#gdZ  & Fgdigdigdi0M01112&33 44455668d88899:;;<V<<  & Fgdigdi#gdZgdi5668c8d8w888888888999U9X99999::1:4:k:n::::;<<<5<8<S<=?????$?8?9?E?L?O?[?b?e?q?x?{????????????tBwBzB˼˼˼˼˼˼hih(5hih(0J$5B*phhih(0J%5B*phh+~h(5hh(0J. h+~h( hih( hihiG<&==???@\AABBBC2CCDDERE%FQFFeGGG(H[Hgdi  & Fgdi#gdZgdigdizBBBBBBBBBBBBBBBBBBBBBBBBBBC1C2CDDDDE EEEQERE[EEEEEEEFF"FQFFFFFFFFGGSGVGbGGGGGGGG[HHHJ:LMM h%Fhi h%Fh(h+~h(5 hih( hihi h+~h(hh(0J.K[HHbIJ:LM6MeN OO:PP QUQQCRR0SSbT|T>UUUxViWXYgdigdi#gdZMMM+MvNNNNNNNNNNNN O/OTOWO_ObOlOoOOOOO9P:P?P@PLPMPpPPPPP Q QCRRRSaTbT>UUUUVVVVVV"V)V0V3V:VAVDVKVRVUV\VcVwVXhih(0J$5B*phhih(0J%5B*ph hih( hihih+~h(5 h+~h( h%Fh(h%Fh(0J.OJQJFXYY YRYUYjYmYqYYYYYYYYYYZZ1Z[Z^ZwZzZZZZZZG[q[t[[[[[[\\\\\-].]]]]]]]effh i imjwj*m;m>mHmnmmmop'p.pppppƹhih(0J$B*phhih(0J%B*phhh(0J. h|h(h+~h(5 h+~h( hih( hihiIYYZ(ZZ>[\]\\\.]]]]^_aajbccc[deefgdi  & Fgdigdi#gdZgdifgh ij+jmjwjjXkkk{llnmmoogqq*s3sstBt"gdi#gdZgdigdippppgqqqorrrrrrsssssttBt\tttuuuuuu u u uu%u&u,u-uFuGubucuuuu̽𞚞yuh(hZhiCJOJQJ^JhZhiB*ph hZhihUjhUUh!5\]^JhZhZ5\]^JhZhZ;CJ\]^J hZhZhZhi hO3,h( hih( hihi h+~h(hh(0J.,Bt\t]tctht}tt $1$IfgdZ1$gdZ$$$d&dNPa$gdZtttttt\QQQQ $1$IfgdZkd$$IfTl\- ,$$s0#44 layt!TttttttZOOOO $1$IfgdZkd$$IfTl\- ,$$s0#44 layt!Ttttttt\QQQQ $1$IfgdZkdL$$IfTl\- ,$$s0#44 layt!TttttttZOOOO $1$IfgdZkd$$IfTl\- ,$$s0#44 layt!Ttttttt\QQQQ $1$IfgdZkd$$IfTl\- ,$$s0#44 layt!TttttttZOOOO $1$IfgdZkd<$$IfTl\- ,$$s0#44 layt!Ttttttt\QQQQ $1$IfgdZkd$$IfTl\- ,$$s0#44 layt!TttttttZOOOO $1$IfgdZkd$$IfTl\- ,$$s0#44 layt!Ttttttt\QQQQ $1$IfgdZkd0$$IfTl\- ,$$s0#44 layt!TttttttZOOOO $1$IfgdZkd$$IfTl\- ,$$s0#44 layt!Ttttttt\QQQQ $1$IfgdZkd|$$IfTl\- ,$$s0#44 layt!TttttttZOOOO $1$IfgdZkd $$IfTl\- ,$$s0#44 layt!Ttttttu\QQQQ $1$IfgdZkd$$IfTl\- ,$$s0#44 layt!Tuuuuuuu u u uZXVVVVVVV"kdl$$IfTl\- ,$$s0#44 layt!T uu-uFuGuPubu $$Ifa$gdi $IfgdiNkd $$IfTH0x$`64 Hayt(T '$$Ifa$gdi $Ifgd!bucusuuuuuuNLLJ'Nkd $$IfTH0x$`64 Hayt(T $$Ifa$gd! $IfgdiNkdy $$IfTH0x$`64 Hayt(Tuuuuuuuuuuuuuv v v vvvvvv h+~h(hU h|h(h!mHnHu*jhiU*h!mHnHujhiUhQhih( h|hQuuuuuuuuBOkd $$IfHU0Z* $ f6$4 HaytOkdC $$IfHU0Z* $ f6$4 Hayt 1$$Ifa$gdi $Ifgdi($a$gdiuu vvvvvv"((gdiOkd $$IfHU0Z* $ &f6$4 Hayt 1$$Ifa$gdi 1$IfgdQ< 0&P:p*<0BP/ =!"#8$% $$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!T$$If!vh#v#v#vs#v:V l0#555s5ayt!Tc$$If!vh#v#v`:V H655`44 Hyt(Tc$$If!vh#v#v`:V H655`44 Hyt(Tc$$If!vh#v#v`:V H655`44 Hyt(Te$$If!vh#v #vf:V HU6$5 5f44 Hayte$$If!vh#v #vf:V HU6$5 5f44 Haytq$$If!vh#v #vf:V HU6$,5 5f944 Hayt3s2&6FVfv2(&6FVfv&6FVfv&6FVfv&6FVfv&6FVfv&6FVfv8XV~ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@_HmH nH sH tH D`D NormalOJQJ^J_HmH sH tH DA D Default Paragraph FontVi@V  Table Normal :V 44 la (k (No List 6"6 HDR$ $*$a$44 FTR$ $*$a$<O< -SCT$ p*$a$5:OR: iPRT$ & F*$@&5:b: SUT$ & F*$@&a$:b: DST$ & F*$@&a$LObL i0ART,$$ & F ``*$@&a$:Ob: 0PR1$ & Fx*$@&a$6Or6 .0PR2$ & F*$@&a$6O6 0PR3$ & F*$@&a$66 PR4$ & F*$@&a$66 PR5$ & F*$@&a$8b8 TB1$ *$^ a$8r8 TB2$`*$^`a$88 TB3$*$^a$88 TB4$*$^a$88 TB5$ *$^ a$&& TCH *$66 TCE!p*$^`p4O"4 EOS"$x*$a$5^o2^ Z0CMT#$*$a$-5;B*OJQJ\]_HmH phsH tH  oA SIB* oQ IPB*/b PRN[&$d!%d$&d!'d$-DM N!O$P!Q$%B* CJOJQJ_HmH phsH tH f`rf Header,Head Project ' "CJOJQJ_HmH sH tH 6 @6 Footer($a$CJaJ6/6 CPR5B*CJOJQJph,/, NUM B*CJph NAMBB SCT + Center ,$a$5D/D SCT Char5OJQJ_HmH sH tH @o@ PR2 CharOJQJ_HmH sH tH  PRN + Verdana 9 pt[/$d!%d$&d!'d$-DM N!O$P!Q$5B* CJph8!8 EOS II0h`h\b@b 2iFootnote Text,Foot Title11$;OJQJ\]N/!N 1iFootnote Text Char;OJQJ\]PK![Content_Types].xmlN0EH-J@%ǎǢ|ș$زULTB l,3;rØJB+$G]7O٭Vc:E3v@P~Ds |w< n v 5zBMXpuv<@ADFHIL^ & 0<[HYfBttttttttttttttu ubuuuv=>?BCEGJKMNOPQRSTUVWXYZ[\]_` !tt8@0(  B S  ? ttttttttt t t tOO&&&mmmmmn   RR&&&mmmmmn 8 *urn:schemas-microsoft-com:office:smarttagsCity9 *urn:schemas-microsoft-com:office:smarttagsplace=*urn:schemas-microsoft-com:office:smarttags PlaceType= *urn:schemas-microsoft-com:office:smarttags PlaceName   $+09:=mprz{~  x,57Bs&v&&&&&CCCCCCFGhhojxjllmmmmm m m mmnnf g 5 6 } qrBD?#@#%%'&,& ''?7F777N NNO#h(hllmmmmm m m mmnn333333333333333333335/QO\\//00BB  B6"88V4V4:D:DGGTTUUbb)k)k*k*kkkkmmmmmmmm m m mmmmmmm nnnn5/QO\\//00BB  B6"88V4V4:D:DGGTTUUbb)k)k*k*kkkkl]l]lllllllmmmmmmmmm m m mmmmmmm nnnn ||T}ij~H%|T1e"n}2+>=۴&<^`.^`.88^8`.^`. ^`OJQJo( ^`OJQJo( 88^8`OJQJo( ^`OJQJo(hh^h`. hh^h`OJQJo( PART -  SCHEDULE  - PRODUCT DATA SHEET  - ``^``.``^``.^`.^`.  ^ `)` ` ^` `)^`o(.^`o(^`o(.^`o(..^`o(... ^`o( .... ^`o( ..... ^`o( ...... `^``o(....... `^``o(........~}| <<0? ש %GOhZ %F3AKe_i(HxPU&K!*?{Q C(mm@ lllln@UnknownG.[x Times New Roman5Symbol3. .Cx Arial7. [ @VerdanaA$BCambria Math"Phhtgtg(wE\ 7E\ 7%ll2qHPi2!xx `lB _C:\Documents and Settings\tintnerv\Application Data\Microsoft\Templates\Spec Master for Doc.dot.SECTION 12 93 00 - SITE AND STREET FURNISHINGSSITE AND STREET FURNISHINGSBAS-12345-MS80Fitzgerald,Richard WFitzgerald,Richard W@         Oh+'0,H ht    0SECTION 12 93 00 - SITE AND STREET FURNISHINGSSITE AND STREET FURNISHINGSFitzgerald,Richard WBAS-12345-MS80Spec Master for DocFitzgerald,Richard W2Microsoft Office Word@@xQ@`@` E\XFYDWACR-487-712%a46b219e-8e28-47c9-9177-0361499f7b5ethttp://fm/groups/cpm/TRG/odgCollormDocumentLibraryFormDocumentLibraryFormffice/2006/metadata/longProperties"/> ?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`acdefghiklmnopqrstuvwxyz{|}~Root Entry F\dData b1Tablej=WordDocument>SummaryInformation(DocumentSummaryInformation8,CompObjrMsoDataStore \d\d !"#%'()+;-./0123456789:A<>?@BCDE  F Microsoft Word 97-2003 Document MSWordDocWord.Document.89qDocument ID GeneratorSynchronous100011000Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.OfficAUEWANXT==2 \d\dItem  ePropertiesP4HOEK14C5AD==2 \d\dItem  x.Properties RNU4T0EZ0Z==2\d\dItem $Properties&PVULEUSSKRX3Z==2\d\dItem *Properties=value="08"/> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. cumentation> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. d:element name="contentStatus" minOccurs="0" maxOccurs=aboration/_layouts/15/DocIdRedir.aspx?ID=SZWXXFYDWACR-487-712, SZWXXFYDWACR-487-7122019-03-01T00:00:00Z;#Ready to Publish;# ;#Master;#12http://www.w3.org/2001/XMLSchema"> e.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100021001Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100041002Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100061003Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerer>Microsoft.Offi > ds:itemID="{5255FBB4-4B6E-4411-9229-1B57759A34AF}" xmlDocumentLibraryF ՜.+,D՜.+,` hp  ARCOM7l /SECTION 12 93 00 - SITE AND STREET FURNISHINGS Title X<p _dlc_DocId_dlc_DocIdItemGuid_dlc_DocIdUrl Published Date to External SiteReady to PublishStatus CSI Division SZWX