ࡱ> ~_ Mbjbjzyzy ;6b6bYD&$ $ $ $ $ 8 8 8 8p L 8 .0!^!(""""""-------$N/2-$ $""$$-$ $ ""-['['['$$ "$ ",['$-['[':'++"<]%+,-0.+ 2%2+2$ +"L=#6['s#,#"""--&""".$$$$2"""""""""B : SECTION 081216 ALUMINUM FRAMES GENERAL RELATED SECTIONS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division01 Specification Sections, apply to this Section. SUMMARY Section Includes: Interior aluminum frames for doors installed in gypsum board partitions. Interior aluminum frames for glazing installed in gypsum board partitions. Interior aluminum doors. REFERENCE STANDARDS The latest published edition of a reference shall be applicable to this Project unless identified by a specific edition date. Reference amendments adopted prior to the effective date of this Contract shall be applicable to this Project. Materials, installation and workmanship shall comply with all applicable requirements and standards. PREINSTALLATION MEETINGS RETAIN "PREINSTALLATION CONFERENCE" PARAGRAPH BELOW IF WORK OF THIS SECTION IS EXTENSIVE OR COMPLEX ENOUGH TO JUSTIFY A CONFERENCE. Preinstallation Conference: Conduct conference at [Project site] . SUBMITTALS Product Data: For each type of product. Include construction details, material descriptions, dimensions of individual components and profiles, [fire-resistance rating,]and finishes. Shop Drawings: For aluminum frames: Include elevations, sections, and installation details for each wall-opening condition. Include details for each frame type, including dimensioned profiles and metal thicknesses. Include locations of reinforcements and preparations for hardware. Include details of anchorages, joints, field splices, connections, and accessories. Include details of moldings, removable stops, and glazing. Samples for Verification: For each type of the following products: Framing Member and Finish: 12 inches (300 mm) long. Include trim. Corner Fabrication and Finish: 12-by-12-inch- (300-by-300-mm-) long, full-size window corner, including full-size sections of extrusions with factory-applied color finish. RETAIN "DOOR FINISH" SUBPARAGRAPH BELOW FOR DOORS IF FURNISHED BY ALUMINUM-FRAME MANUFACTURER. Door Finish: Manufacturer's standard-size unit, but not less than 3 inches (75 mm) square. Product Schedule: For aluminum frames.Use same designations indicated on Drawings. Coordinate with door hardware schedule and glazing. Maintenance Data: For aluminum frames to include in maintenance manuals. QUALITY ASSURANCE Installer Qualifications: An experienced installer who has completed interior aluminum framing systems similar in material, design, and extent to those indicated for this Project and whose work has resulted in construction with a record of successful in-service performance. Manufacturer Qualifications: A firm experienced in manufacturing interior aluminum framing systems similar to those indicated for this Project for five (5) years and with a record of successful in-service performance. Source Limitations: Obtain aluminum frames through one (1) source from a single manufacturer with the capacity and resources to provide products of consistent quality in appearance and physical properties. Product Options: Drawings indicate dimensions, arrangements, alignment, and profiles of components and assemblies as they relate to sightlines, to one another, and to adjoining construction size. Other manufacturers products complying with requirements may be considered. Do not modify intended aesthetic effects, as judged solely by Architect, except with Architects approval. If modifications are proposed, submit comprehensive explanatory data to Architect for review. Fire-Rated Door Frames: Frames complying with NFPA 80 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated based on testing according to NFPA 252. Mockups: Build mockups to verify selections made under Sample submittals and to demonstrate aesthetic effects and to set quality standards for fabrication and installation. INDICATE PORTION OF WALL REPRESENTED BY MOCKUP ON DRAWINGS OR DRAW MOCKUP AS SEPARATE ELEMENT. Build mockup of each type of aluminum frame[and door] in typical wall area as shown on Drawings. Approval of mockups does not constitute approval of deviations from the Contract Documents contained in mockups unless Architect and Owner specifically approve such deviations in writing. RETAIN SUBPARAGRAPH BELOW IF THE INTENTION IS TO MAKE AN EXCEPTION TO THE DEFAULT REQUIREMENT IN SECTION014000 "QUALITY REQUIREMENTS" FOR DEMOLISHING AND REMOVING MOCKUPS. Subject to compliance with requirements, approved mockups may become part of the completed Work if undisturbed at time of Substantial Completion. DELIVERY, STORATE, AND HANDLING Deliver aluminum frames cartoned or crated to provide protection during transit and job storage. Inspect aluminum frame work upon delivery for damage. Minor damages may be repaired provided the repaired items are equivalent in all respects to new work; otherwise remove and replace damaged work as directed. PRODUCTS PRODUCTS, GENERAL Materials shall meet or exceed all applicable referenced standards, federal, state and local requirements, and conform to codes and ordinances of authorities having jurisdiction. MANUFACTURERS Manufacturers: Subject to compliance with requirements, provide products by one of the following: HYPERLINK "http://www.specagent.com/LookUp/?uid=123456789346&mf=04&src=wd"Advanced Architectural Frames. HYPERLINK "http://www.specagent.com/LookUp/?uid=123456809611&mf=04&src=wd"Dual Lock Partition Systems, Inc.; Avalon International Aluminum. Frameworks, an ASSA ABLOY Group company. HYPERLINK "http://www.specagent.com/LookUp/?uid=123456809613&mf=04&src=wd"Modulex, Inc; Division of Pacific National Group. HYPERLINK "http://www.specagent.com/LookUp/?uid=123456789350&mf=04&src=wd"RACO Interior Products, Inc. HYPERLINK "http://www.specagent.com/LookUp/?uid=123456789351&mf=04&src=wd"Versatrac. RETAIN OPTION IN "SOURCE LIMITATIONS" PARAGRAPH BELOW FOR DOORS IF FURNISHED BY ALUMINUM-FRAME MANUFACTURER. Source Limitations: Obtain aluminum frames[and frame-manufacturer's doors] from single source from single manufacturer. PERFORMANCE REQUIREMENTS RETAIN "FIRE-RATED FRAMES" PARAGRAPH BELOW IF APPLICABLE. REVISE TO ALLOW NEUTRAL-PRESSURE TESTING IF REQUIRED AND ACCEPTABLE TO AUTHORITIES HAVING JURISDICTION. NOT ALL LISTED MANUFACTURERS' PRODUCTS ARE TESTED AT POSITIVE PRESSURE. Fire-Rated Frames: Frames for fire-rated door assemblies complying with NFPA80 that are listed and labeled by a qualified testing agency, for fire-protection ratings indicated, based on testing at positive pressure according to [NFPA252] [or] [UL10C]. RETAIN "OVERSIZE FIRE-RATED FRAMES" SUBPARAGRAPH BELOW IF APPLICABLE AND ACCEPTABLE TO AUTHORITIES HAVING JURISDICTION. Oversize Fire-Rated Frames: For units exceeding sizes of tested assemblies, provide certification by a qualified testing agency that frames comply with standard construction requirements for tested and labeled fire-rated frames except for size. RETAIN "FRAMES FOR SMOKE- AND DRAFT-CONTROL ASSEMBLIES" SUBPARAGRAPH BELOW IF REQUIRED. THE IBC REQUIRES FIRE DOOR ASSEMBLIES TO COMPLY WITH SMOKE- AND DRAFT-CONTROL REQUIREMENTS IN CORRIDORS, SMOKE BARRIERS, AND SMOKE PARTITIONS. Frames for Smoke- and Draft-Control Assemblies: Tested according to UL1784 and installed in compliance with NFPA105. TESTED PRESSURE DIFFERENTIAL IN "AIR LEAKAGE RATE" SUBPARAGRAPH BELOW IS THE MOST STRINGENT REQUIRED BY NFPA105; THE IBC REQUIRES A 0.1-INCH WG (24.9 PA) OF PRESSURE DIFFERENTIAL; REVISE TO SUIT PROJECT. VERIFY REQUIREMENTS OF AUTHORITIES HAVING JURISDICTION. Air Leakage Rate: Maximum air leakage of 0.3 cfm/sq.ft. (0.9 cu.m per minute/sq.m) at the tested pressure differential of 0.3-inch wg (75 Pa). COMPONENTS Aluminum Framing: ASTMB221 (ASTMB221M), with alloy and temper required to suit structural and finish requirements, and not less than 0.062 inch (1.6 mm) thick. RETAIN "DOOR FRAMES" PARAGRAPH BELOW IF REQUIRED. Door Frames: Extruded aluminum, reinforced for hinges, strikes, and closers. RETAIN "GLAZING FRAMES" PARAGRAPH BELOW IF REQUIRED. Glazing Frames: Extruded aluminum, for indicated glass thickness. RETAIN "DOOR TRACKS" PARAGRAPH BELOW IF DOOR TRACKS SUCH AS FOR SLIDING DOORS ARE EXPOSED. Door Tracks: Extruded aluminum where exposed, sized to enclose sliding-door hardware, and in finish matching frame and trim finish. Trim: Extruded aluminum, not less than 0.062 inch (1.6 mm) thick; removable, snap-in casing trim, glazing stops and door stops, without exposed fasteners. RETAIN ONE OF TWO "DOORS" PARAGRAPHS BELOW. IF RETAINING FIRST PARAGRAPH, DELETE SECOND PARAGRAPH AND SUBPARAGRAPHS. RETAIN SECOND FOR DOORS IF FURNISHED BY ALUMINUM-FRAME MANUFACTURER. INDICATE DOOR HEIGHTS, WIDTHS, AND ELEVATIONS ON DRAWINGS. Doors: As specified in [Section081416 "Flush Wood Doors."] [Section084113 "Aluminum-Framed Entrances and Storefronts."]. Doors: Manufacturer's standard, factory-assembled, 1-3/4-inch- (45-mm-) thick, aluminum-framed door construction. OPTIONS IN "DOOR OPERATION" SUBPARAGRAPH BELOW ARE EXAMPLES OF AVAILABLE TYPES. CONSULT MANUFACTURERS FOR AVAILABILITY. Door Operation: [Sliding] [Swinging]. DELETE "STILES" AND "RAILS" SUBPARAGRAPHS BELOW IF DIMENSIONED ON DRAWINGS. LAST OPTION IN FIRST SUBPARAGRAPH IS AN EXAMPLE OF MEDIUM-STILE WIDTH. OPTIONS IN SECOND SUBPARAGRAPH ARE EXAMPLES ONLY. CONSULT MANUFACTURERS FOR AVAILABILITY. Stiles: [Narrow] [Medium] [Wide] [3-3/4 inches (95 mm)]. Rails: [3-3/4-inch (95-mm)] [6-inch (152-mm)] top rail and [6-inch (152-mm)] [9-1/2-inch (241-mm)] bottom rail. RETAIN "DOOR FINISH" PARAGRAPH BELOW IF DOORS ARE FURNISHED BY ALUMINUM-FRAME MANUFACTURER. Door Finish: [Match frame and trim finish] [Clear-anodized aluminum] [Color-anodized aluminum] [Factory-applied, baked-enamel or powder-coat finish] [High-performance organic finish]. RETAIN "COLOR" SUBPARAGRAPH BELOW IF DOOR FINISH IS COLOR-ANODIZED ALUMINUM, BAKED-ENAMEL OR POWDER-COAT FINISH, OR HIGH-PERFORMANCE ORGANIC FINISH. Color: [As indicated by manufacturer's designations] [Match Architect's sample] [As selected by Architect from manufacturer's full range] [Light bronze] [Medium bronze] [Dark bronze] [Black]. Frame and Trim Finish: [Clear-anodized aluminum] [Color-anodized aluminum] [Factory-applied, baked-enamel or powder-coat finish] [High-performance organic finish]. RETAIN "COLOR" SUBPARAGRAPH BELOW IF FRAME FINISH IS COLOR-ANODIZED ALUMINUM, BAKED-ENAMEL OR POWDER-COAT FINISH, OR HIGH-PERFORMANCE ORGANIC FINISH. Color: [As indicated by manufacturer's designations] [Match Architect's sample] [As selected by Architect from manufacturer's full range] [Light bronze] [Medium bronze] [Dark bronze] [Black]. ACCESSORIES RETAIN ONE OR MORE OF PARAGRAPHS BELOW TO SUIT PROJECT. Fasteners: Aluminum, nonmagnetic, stainless-steel or other noncorrosive metal fasteners compatible with frames, stops, panels, reinforcement plates, hardware, anchors, and other items being fastened. MATERIALS IN "DOOR SILENCERS," "SMOKE SEALS," AND "GLAZING GASKETS" PARAGRAPHS BELOW MAY BE AVAILABLE FROM SOME MANUFACTURERS IN A CHOICE OF COLORS. Door Silencers: Manufacturer's standard continuous mohair, wool pile, or vinyl seals in black color. RETAIN "SMOKE SEALS" PARAGRAPH BELOW IF RETAINING "FRAMES FOR SMOKE- AND DRAFT-CONTROL ASSEMBLIES" SUBPARAGRAPH IN "PERFORMANCE REQUIREMENTS" ARTICLE. Smoke Seals: Intumescent strip or fire-rated gaskets in black. Glazing Gaskets: Manufacturer's standard extruded or molded rubber or plastic, to accommodate glazing thickness indicated; in black. Glass: As specified in [Section088000 "Glazing."] [Section088113 "Decorative Glass Glazing."] [Section088400 "Plastic Glazing."] MOST MANUFACTURERS THAT OFFER DOORS DO NOT OFFER DOOR HARDWARE FOR SWINGING DOORS. CONSULT MANUFACTURERS FOR HARDWARE AVAILABILITY. Door Hardware: As specified in Section087100 "Door Hardware." and Section087101 "Door Hardware Schedule", unless noted otherwise. FABRICATION Provide concealed corner reinforcements and alignment clips for accurately fitted hairline joints at butted and mitered connections. Factory prepare aluminum frames to receive templated mortised hardware; include cutouts, reinforcements, mortising, drilling, and tapping, according to the Door Hardware Schedule and templates furnished as specified in Section087100 "Door Hardware" and Section087101 "Door Hardware Schedule. Locate hardware cutouts and reinforcements as required by fire-rated label for assembly. Fabricate frames for glazing with removable stops to allow glazing replacement without dismantling frame. Locate removable stops on the inside of spaces accessed by keyed doors. Fabricate components to allow secure installation without exposed fasteners. GENERAL FINISH REQUIREMENTS Appearance of Finished Work: Noticeable variations in same piece are not acceptable. Variations in appearance of adjoining components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. ALUMINUM FINISHES IF RETAINING MORE THAN ONE FINISH IN PARAGRAPHS BELOW, INDICATE LOCATION OF EACH ON DRAWINGS OR BY INSERTS. Clear Anodic Finish: AAMA611, AA-M12C22A31, ClassII, 0.010 mm or thicker. Color Anodic Finish: AAMA611, AA-M12C22A32/A34, ClassII, 0.010 mm or thicker. "BAKED-ENAMEL OR POWDER-COAT FINISH" PARAGRAPH BELOW REFERENCES AAMA STANDARD FOR PIGMENTED ORGANIC COATING ON EXTRUSIONS AND PANELS. Baked-Enamel or Powder-Coat Finish: AAMA2603 except with a minimum dry film thickness of 1.5 mils (0.04 mm). Comply with coating manufacturer's written instructions for cleaning, conversion coating, and applying and baking finish. ONLY A FEW MANUFACTURERS OFFER HIGH-PERFORMANCE FINISHES; VERIFY AVAILABILITY. IF SPECIFIC PRODUCTS ARE REQUIRED, NAME COATING MANUFACTURERS AND PRODUCTS. High-Performance Organic Finish: Two-coat fluoropolymer finish complying with AAMA2604 and containing not less than [50] [70] percent PVDF resin by weight in color coat. Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. EXECUTION EXAMINATION Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work. Verify that wall thickness does not exceed standard tolerances allowed by throat size of indicated aluminum frame. Proceed with installation only after unsatisfactory conditions have been corrected. INSTALLATION Install aluminum frames plumb, rigid, properly aligned, and securely fastened in place; according to manufacturer's written instructions. RETAIN OPTION IN SUBPARAGRAPH BELOW IF SMOKE-CONTROL ASSEMBLIES ARE REQUIRED. THE IBC REQUIRES FIRE-DOOR ASSEMBLIES TO COMPLY WITH SMOKE- AND DRAFT-CONTROL REQUIREMENTS IN CORRIDORS, SMOKE BARRIERS, AND SMOKE PARTITIONS. At fire-protection-rated openings, install fire-rated frames according to NFPA80[and NFPA105]. Install frame components in the longest possible lengths with no piece less than 48 inches (1220 mm); components [72 inches (1830 mm)] [96 inches (2450 mm)] or shorter shall be one piece. RETAIN FIRST SUBPARAGRAPH BELOW IF FRAMES ARE ATTACHED TO SUSPENDED CEILING. Fasten to suspended ceiling grid on maximum 48-inch (1220-mm) centers, using sheet metal screws or other fasteners approved by frame manufacturer. Use concealed installation clips to produce tightly fitted and aligned splices and connections. Secure clips to extruded main-frame components and not to snap-in or trim members. Do not leave screws or other fasteners exposed to view when installation is complete. Glass: Install glass according to [Section088000 "Glazing" and] [Section088113 "Decorative Glass Glazing" and] [Section088400 "Plastic Glazing" and] aluminum-frame manufacturer's written instructions. RETAIN "DOORS" AND "DOOR HARDWARE" SUBPARAGRAPHS BELOW FOR DOORS IF FURNISHED BY ALUMINUM-FRAME MANUFACTURER. Doors: Install doors aligned with frames and fitted with required hardware. Door Hardware: Install according to Section087100 "Door Hardware" and Section087101 "Door Hardware Schedule" and aluminum-frame manufacturer's written instructions. ADJUSTING Inspect installation, correct misalignments, and tighten loose connections. RETAIN "DOORS" PARAGRAPH BELOW IF DOORS ARE FURNISHED BY ALUMINUM-FRAME MANUFACTURER. Doors: Adjust doors to operate smoothly and easily, without binding or warping. Adjust hardware to function smoothly, and lubricate as recommended by manufacturer. Clean exposed frame surfaces promptly after installation, using cleaning methods recommended in writing by frame manufacturer and according to AAMA609 & 610. OPTION IN "TOUCH UP" PARAGRAPH BELOW IS INCLUDED IN SEVERAL MANUFACTURERS' PRINTED LITERATURE; IT REQUIRES SUBJECTIVE JUDGMENT. Touch Up: Repair marred frame surfaces to blend inconspicuously with adjacent unrepaired surface[so touchup is not visible from a distance of 48 inches (1220 mm)] as viewed by Architect. Remove and replace frames with damaged finish that cannot be satisfactorily repaired. END OF SECTION 08 12 16 FOR MDACC USE ONLY. DELETE THIS PAGE BEFORE ISSUING DOCUMENTS. document revision history IssueDateRevision DescriptionAuthor20190301Original IssuanceRev. 1.Rev. 2Rev. 3 Rev. 4 Rev. 5      MD ANDERSON Project No. XXXXXXMD ANDERSON PROJECT NAMEA/E Name Issue Description A/E Project No.Month 00, 0000 鶹ӳ prefabricated interior aluminum frames MD Anderson Cancer Center08 12 16MS 20190301 PAGE 9 of  NUMPAGES 9 !)   %4<DKs0`˿ᴫᴫ˿ᜫݑݍ˿ᅺhjhy05h\/hi hP{hy0hP{hy00J0 hP{0J/hP{hP{0J/ hy00J0 hy05hjhy05<CJhjhi5<CJ h-0@h-0hy0hihy00J.5hihi5hihv54!):< 2    * 5 )gdy~%gdy~%gdy~%gdy~%gdy~%$ H*$a$gdy~% 'bM0D`!>gdy~%)gdy~%gdy~%gdy~%>[s|AO jkl#$%UVXY˽ҮˠҮˑ˃ҮuҮjhP{hP{UjhP{hP{Uh-0h30J9>*B*phjhP{hP{UhP{hP{0J9>*B*phjhP{hP{U hP{hP{jhP{hP{U hEhP{hP{h\/h-0hy0hjhy05<CJ*s|AOX  !"|"q#X$$%gdy~%)gdy~% $a$gdy~%gdy~%gdy~%gdy~% !!!!!!!""{"|"q#W$X$$%%% & &)&Q&\&]&d&&&&&&'' ''F'G'''''' (ĸĸĸĸĸĸĸ hthy0 hP{0J/hP{hP{0J/ hy00J0 hy05hjhy05hy0hjhy05<CJhjhi5<CJ hP{hP{hP{hP{0J9>*B*phjhP{hP{UjhP{hP{U6%f&q&'G''' (f(()z**k++ ,,0---.I/ 00C1gdy~%)gdy~%gdy~%gdy~%gdi (e(f((()))$)?)J)K)L)Y)Z)])^)h))y*z**********,+7+8+@+k++++++++,, ,,,-- -----%-&---伴䢞ΐ hP{0J/5 hy00J05hGJ hy05hihP{ hy~%5hjhP{5hjhy05ht hP{0J/hP{hP{0J/ hy00J0 hthy0hy0hjhy05<CJhjhi5<CJ8--/-8-B-C-J-M-S-T-\-l-r-s-{-~------- .%.(.?.B.Y.\.....H/I/Q/|///////////00!080;0R0U00000B1C1K1v1y1111111111122F2 hy05 hP{hy0hjhy05<CJhjhi5<CJ hP{0J/5hP{hP{0J/ hy00J05hy0hGJJC122G233 444d55r667789z99:+:&;8;;;@<gdy~%)gdy~%gdy~%gdy~%F2G233334 44444]5b5{555555555q6r66666666666666666g8o8w888888888888;;;@<<< =(=)=2==H>»»ɻ»»ɻ𵬦 hP{0J/hP{hP{0J/ hy00J0 hthP{ hthy0hthjhP{5hjhy05 hvhy0hjhi5<CJhy0hjhy05<CJA@<<=I>y???G@@AAABBCCDD3EE[FFGGGgdy~%gdy~%gdy~%gdy~%)gdy~%H>I>>>>>ABBBB5C>C?CHCVC_C`CiClCuCvCCCCCD D*DEEEEEFF&F[FFF9GAGIGfGlGmGnG~GGGHkHlHмм𢚢𓌓 h~Yh~Y h~YhP{ h~Yhy0hjhP{5hjhy05hthP{0J/hthy00J0 hP{0J/5 hy00J05 hP{0J/hP{hP{0J/ hy00J0hjhi5<CJ hy05hy0hjhy05<CJ4GHlHII/JAKYKKKKKKKK $1$Ifgd&1$gd&$$$d&dNPa$gd&)gdV '$a$gdy~%)gdy~%gdy~%lHI.J/JJJJJJAKOKXKYKZKKKKKXLYLZL_L`LeLfLkLlLqLLLLLxtxtxtxtj\j\h-0h-0B*\]phh-0h-0\]h3tjh3tUh}!5\]h&h&5\]^Jh&h&;CJ\]^Jhth&5;<\]^Jhth&<h&hhP{ hP{0J/5hP{hP{0J/ hy00J05 hy05hjhy05<CJhjhi5<CJhy0KKKKKK^SSSS $1$Ifgd&kd#$$IfTl\,$$0$44 layt?jTKKKKKK\QQQQ $1$Ifgd&kd$$IfTl\,$$0$44 layt?jTKKLLLL^SSSS $1$Ifgd&kd[$$IfTl\,$$0$44 layt?jTLL L LLL\QQQQ $1$Ifgd&kd$$IfTl\,$$0$44 layt?jTLLLLLL^SSSS $1$Ifgd&kd$$IfTl\,$$0$44 layt?jTLLLLLL\QQQQ $1$Ifgd&kd-$$IfTl\,$$0$44 layt?jTL L!L"L#L$L^SSSS $1$Ifgd&kd$$IfTl\,$$0$44 layt?jT$L%L-L.L/L0L\QQQQ $1$Ifgd&kde $$IfTl\,$$0$44 layt?jT0L1L2L3L4L5L^SSSS $1$Ifgd&kd $$IfTl\,$$0$44 layt?jT5L6L>L?L@LAL\QQQQ $1$Ifgd&kd $$IfTl\,$$0$44 layt?jTALBLCLDLELFL^SSSS $1$Ifgd&kd; $$IfTl\,$$0$44 layt?jTFLGLOLPLQLRL\QQQQ $1$Ifgd&kd $$IfTl\,$$0$44 layt?jTRLSLTLULVLWL^SSSS $1$Ifgd&kds $$IfTl\,$$0$44 layt?jTWLXLYL[L\L]L^L_LaL\RPPKPPPgdi '$a$gdy~%kd $$IfTl\,$$0$44 layt?jTaLbLcLdLeLgLhLiLjLkLmLnLoLpLqLLL$ !$1$Ifa$gd-0 $1$IfgdhqgdiLLLLLLM-MHMQMRMTMXM]M^M_MeMfMgMhMlMmMwMxMyMzM{M|M~MMMh3th}!;\]mHnHu*!jh-0h-0;U\]*h}!;\]mHnHujh-0h-0;U\]hV;\]hj;\]hi;\]hVhy0h-0h-0\]h-0h-0;\]LLLLLLLJ< $$1$Ifa$gdhqNkd$$IfTH0x$`64 Haytm0T $$1$Ifa$gd-0 $1$Ifgd-0Nkd $$IfTH0x$`64 Haytm0TLLLLLLM-M $$1$Ifa$gd-0 $1$Ifgd-01$gd-02gdy~%2gdiNkdu$$IfTH0x$`64 Haytm0T-M.MHMQMRM^M{MPE $1$IfgdVJkdA$$IfHU0$ $ $4 Halytm0 $$1$Ifa$gd-0 $1$Ifgd-0Jkd$$IfHU0$ $ $4 Halytm0{M|M}M~MMM '$a$gdy~%4gdy~%4gdiJkd$$IfHU0$ $ &$4 Halytm091:pP{<0BP/ =!"#0$% DyK yK http://www.specagent.com/LookUp/?uid=123456789346&mf=04&src=wdyX;H,]ą'cDyK yK http://www.specagent.com/LookUp/?uid=123456809611&mf=04&src=wdyX;H,]ą'cDyK yK http://www.specagent.com/LookUp/?uid=123456809613&mf=04&src=wdyX;H,]ą'cDyK yK http://www.specagent.com/LookUp/?uid=123456789350&mf=04&src=wdyX;H,]ą'cDyK yK http://www.specagent.com/LookUp/?uid=123456789351&mf=04&src=wdyX;H,]ą'c$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jT$$If!vh#v#v#v#v:V l0$5555yt?jTc$$If!vh#v#v`:V H655`44 Hytm0Tc$$If!vh#v#v`:V H655`44 Hytm0Tc$$If!vh#v#v`:V H655`44 Hytm0Te$$Ifl!vh#v #v:V HU$5 544 Halytm0e$$Ifl!vh#v #v:V HU$5 544 Halytm0q$$Ifl!vh#v #v:V HU$,5 5944 Halytm0Bs666666666vvvvvvvvv666666>6666666666666666666666666666666666666666666666666hH6666666666666666666666666666666666666666666666666666666666666666662 0@P`p2( 0@P`p 0@P`p 0@P`p 0@P`p 0@P`p 0@P`p8XV~ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@_HmH nH sH tH D`D NormalOJQJ^J_HmH sH tH DA`D Default Paragraph FontVi@V 0 Table Normal :V 44 la (k ( 0No List :: HDR$ $*$a$CJ88 FTR$ $*$a$CJ4"4 SCT$*$a$5@O"@ PRT$$ & F*$@&a$5:b: SUT$ & F*$@&a$:b: DST$ & F*$@&a$<OR< ?ART$$ & F*$@&a$:Ob: =PR1$ & F*$@&a$>Or> APR2$ & F *$@&a$>O> PR3$ & F *$@&a$>> PR4$ & F  *$@&a$>> PR5$ & F ` *$@&a$8b8 TB1$ *$^ a$8r8 TB2$`*$^`a$88 TB3$*$^a$88 TB4$*$^a$88 TB5$ *$^ a$88 TF1 $ *$^ a$88 TF2!$`*$^`a$88 TF3"$*$^a$88 TF4#$*$^a$88 TF5$$ *$^ a$&R& TCH%*$6b6 TCE&p*$^`p4Or4 EOS'$*$a$5:: ANT($*$a$ >*<B* 6O6 70CMT)$*$a$<B* CPR SPN SPD NUMO NAM&o& SI B*ph&o& IP B*ph,, RJUST1$a$4@"4 3Z10Header 2 H$.1. 2Z10 Header Char4 @B4 5Z10Footer 4 H$.Q. 4Z10 Footer Chartbt 8XTIPJ6$d%d&d'dNOPQ B* ph8@/q@ )XCMT Char<B*OJQJ^Jph4/4 6XTIP Char <B* ph8:o: A SAhyperlink >*B*phl 6U 6 A0 Hyperlink >*B*ph <vOMNd;$x$d%d&d'd*$-DM NOPQa$B* CJOJQJ^JaJphZ/Z ;vOMN Char1<B* CJOJQJ^JaJfHphq 4/4 P{PR1 Char OJQJ^J*W * v`Strong5\4/4 -0ART Char OJQJ^J>> -0TITLE@1$5;OJQJ\]0/0 -0PR2 CharOJQJPK![Content_Types].xmlN0EH-J@%ǎǢ|ș$زULTB l,3;rØJB+$G]7O٭Vc:E3v@P~Ds |w< E %%%( (--F2H>lHLM'*,./135E %C1@<GKKKLLLL$L0L5LALFLRLWLaLLL-M{MM()+-0246789:;<=>?@ABCDFGHIk$UXEXXXXX  (!tt8@0(  B S  ?DDD:EAEEDEE@EGEE=*urn:schemas-microsoft-com:office:smarttags PlaceType8*urn:schemas-microsoft-com:office:smarttagsCity9*urn:schemas-microsoft-com:office:smarttagsState V^%,.1Z\//YD^D_DdDeDjDkDpDqD~EE::<<BBYD^D_DdDeDjDkDpDqD~EE333333""""XCXDYDYD_D_DeDeDkDkDDDDDDDDDRE]E^EhElEzE|E|E}E}EE""""XCXDYDYD_D_DeDeDkDkDDDDDDDDDRE]E^EhElEzE|E|E}E}EE?6AYI0/ PART -  SCHEDULE  - PRODUCT DATA SHEET  - ``^``.``^``.^`.^`.  ^ `)` ` ^` `)PART -  SCHEDULE  - PRODUCT DATA SHEET  - ....))YI R<0 MASTERSPEC+*3tvut}!w#y~%\/-0Z1-8.C=DGJ{pJnPX*Q](kmhq5tP{m0~Y3jVqt*&y0+?jAWiYD[DDOIFormatMF04MF95 SectionIDSpecTypeVersion12/01/13108121608125209 MasterSpec8956@CCCCE@UnknownG.[x Times New Roman5Symbol3. .Cx Arial7. [ @VerdanaA$BCambria Math"hhtgtg3 &: "|3 &: "|!7D7DJqHP  $PZ12!xxh  SECTION 081216 - ALUMINUM FRAMESALUMINUM FRAMESBAS-12345-MS80Fitzgerald,Richard WFitzgerald,Richard W  Oh+'0  <H h t $SECTION 081216 - ALUMINUM FRAMESALUMINUM FRAMESFitzgerald,Richard WBAS-12345-MS80NormalFitzgerald,Richard W3Microsoft Office Word@F#@拿\@,O\ 3 &: ?@ABCDEFGHIJLMNOPQRSUVWXYZ[\]^_`abcdefghijklmopqrstuwxyz{|}Root Entry FData K1TableT 3WordDocument;SummaryInformation(nDocumentSummaryInformation8,CompObjrMsoDataStore   !"#$%'()+H-./0123456789:;<=>?@ABCDEFGNIKLMOPQR  F Microsoft Word 97-2003 Document MSWordDocWord.Document.89q /sharepoint/events">Document ID GeneratC1K4OPTUMXYN0A==2 Item  PropertiesCPM4UN5WW==2 Item  vx.PropertiesDJKQU4IV1S0UQ==2Item  eProperties&EOGJS12GESLI1L0Q==2Item *PropertiesJsd:enumeration value="33"/> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. t ref="dc:subject" minOccurs="0" maxOccurs="1"/> DocumentLibraryFormDocumentLibraryFormffice/2006/metadata/longProperties"/> > Token=71e9bce111e9429cMicrosoft.OfficDocument ID GeneratorSynchronous100011000Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100021001Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100041002Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100061003Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandler">DocumentLibraryF ds:itemID="{25BEE110-DC26-4418-8B97-B21B9CBF6169}" xmlDocumentLibraryF ՜.+,D՜.+,L hp|  |"7D !SECTION 081216 - ALUMINUM FRAMES Title X$<,<\  _PID_HLINKS _dlc_DocId_dlc_DocIdItemGuid_dlc_DocIdUrl CSI DivisionStatus Published Date to External Site Ready to PublishA2z ?http://www.specagent.com/LookUp/?uid=123456789351&mf=04&src=wd3z ?http://www.specagent.com/LookUp/?uid=123456789350&mf=04&src=wd=q?http://www.specagent.com/LookUp/?uid=123456809613&mf=04&src=wd?q?http://www.specagent.com/LookUp/?uid=123456809611&mf=04&src=wd5{?http://www.specagent.com/LookUp/?uid=123456789346&mf=04&src=wdSZWXXFYDWACR-487-665%cb719717-a6f4-4229-92b3-4c822b09c0d4thttp://fm/groups/cpm/TRG/odgCollaboration/_layouts/15/Do